Injector Data And Fuel Pressure

vpap1 · Jul 2, 2014

I'm tuning a mild 347 combo with binary editor, Gufb. Now everyone says keep stock fuel pressure and tune but injector data says it's rated at 44 psi. Car started and ran a bit at 44 psi but not 39.5. Or do I need to look else where in the tune to adjust and hold the fuel pressure at 39.5?
Thanks

jrichker · Jul 2, 2014

If the injectors deliver their rated flow a 44 PSI, that is where you should run them. Running the at 39 PSI will work, but they will deliver less fuel.

Playing with fuel pressure to adjust overall Air/Fuel ratio only works well when the mixture is rich or lean throughout the range of operation. If it is rich at the bottom and lean at the top end of the power curve, turning up the fuel pressure will richen up the Air/Fuel ratio throughout the power curve. Too much fuel at low RPM's can make the engine run rough and be sluggish.

With a wide band O2 sensor and the ability to change the injector pulse width, the small difference in fuel pressure shouldn't make much difference.

Fuel injector sizing & injector photos

Revised 11-Dec-2011 to add larger injector sizes to injector table

Injector HP ratings: divide flow rating by.5 and multiply the result by the number of injectors. This uses a 100% duty cycle. These ratings are for naturally aspirated engines at the flywheel.

Example:
19/.5 = 38, 38 x 8 = 304 HP
24/.5 = 48, 48 x 8 = 384 HP
30/.5 = 60, 60 x 8 = 480 HP
36/.5 = 72, 72 x 8 = 576 HP
42/.5 = 84, 84 x 8 = 672 HP

The preferred duty cycle is about 85% maximum, so for a safety factor multiply the final figure times .85.

19/.5 = 38, 38 x 8 = 304 HP x .85 = 258 HP
24/.5 = 48, 48 x 8 = 384 HP x .85 = 326 HP
30/.5 = 60, 60 x 8 = 480 HP x .85 = 408 HP
36/.5 = 72, 72 x 8 = 576 HP x .85 = 490 HP
42/.5 = 84, 84 x 8 = 672 HP x .85 = 571 HP

Remember that the above ratings are at 39 PSI. Increasing the pressure will effectively increase the flow rating. Example: a 19 lb injector will flow 24 lbs at 63 PSI, and a 24 lb injector will flow 30 lbs at 63 PSI.

See http://users.erols.com/srweiss/calcpchg.htm to get the calculators used in these examples.

Here's the duty cycle explanation. Duty cycle is how much of the time the intake is open the injectors are turned on. The 85% figure means that for 85% of the time the intake valve is open, the injectors are spraying. The idea is that you want some percentage of the duty cycle left over so that you have some room to grow the process.

If you are at 100% and you need more fuel, all you can do is turn up the fuel pressure. That means the whole fuel curve from idle to WOT is affected. Maybe you are already too rich at idle, and turning up the fuel pressure makes it worse. If you had some injector duty cycle left to play with, a custom tune could use that where it is needed. That would not over richen the whole range from idle to WOT.

If you did turn up the fuel pressure, you might be able to change the injector duty cycle to get the air/fuel mixture ratio you want since the injectors will have extra fuel delivery capability.

With larger than stock injectors or higher that stock fuel pressure, you will need an aftermarket MAF that matches the injector size. The MAF “lies” to the computer to get a fuel delivery schedule that meets the engine’s needs and isn’t too rich or too lean. The best strategy is an aftermarket MAF and a custom tune to insure the best air/fuel ratio over all the RPM range.

Don't forget to increase the fuel pump size when you increase injector size or significantly increase the fuel pressure

Diagram courtesy of Tmoss & Stang&2birds

vpap1 · Jul 7, 2014

Awesome info thanks

Injector Data And Fuel Pressure

vpap1

Member

jrichker

StangNet's favorite TOOL

vpap1

Member

Similar threads

Injector Data And Fuel Pressure

vpap1

Member

jrichker

StangNet's favorite TOOL

vpap1

Member

Similar threads

Privacy & Transparency

Privacy & Transparency