Injector question

arrickburke · Sep 14, 2026

I just bought a 94 mustang GT and was wondering if these injectors are the correct ones for it. I've seen where they are and then they aren't.

LILCBRA · Sep 14, 2026

They look correct as near as I can tell.

Bullitt347 · Sep 14, 2026

arrickburke said:
I just bought a 94 mustang GT and was wondering if these injectors are the correct ones for it. I've seen where they are and then they aren't.

Why are you asking?
Is there a driveability concern?

rednotch · Sep 14, 2026

Look like cheapy China 19lb knock off Bosch replacement injectors

arrickburke · Sep 14, 2026

So I bought the car with the cats taken off the car and looks like they were in the process of putting on short headers and then stopped working on it. It doesn't run without playing with the throttle. Put i looked at them when I was in the process of buying it and thought they didn't look stock so I looked them up and they said they where for a 4.6 liter not a 5.0. I just want to make sure they are correct or going to work so it doesnt run lean and I have a meltdown.

AeroCoupe · Sep 14, 2026

If you can pull one and get better pictures. If they don’t have “Motorcraft” in the yellow part I would bet $$$ they are aftermarket.

DadLife0724 · Sep 14, 2026

Definitely needs pictures dude.

arrickburke · Sep 14, 2026

DadLife0724 said:
Definitely needs pictures dude.

I will try to get more tomorrow i just had this one from where I looked up the part number.

Qtrhrse23 · Sep 14, 2026

Yea more pictures, BUT those white numbers(902-101) ARE SUSPECT. Been awhile but dont remember those. Knockoffs is my vote.

manicmechanic007 · Sep 19, 2026

I run those cheap china Motorcrafts all the time
True the last set I put in had 1 bad one
46 bucks for 8
Just buy 8 more and replace them as needed
Otherwise, I just get known? good ones from the junkyard and clean those
Don't see many bad injectors, I see a lot that need cleaning

Mustang5L5 · Sep 19, 2026

I doubt those are genuine injectors. Most likely Amazon/ebay knock offs.

The OE ford injectors will have a ford engineering part number on the top plastic and some have a ford oval (not all). I forget if it was Bosch or Denso making them in the early 90s.

Genuine replacement injectors won’t have the ford branding and engineering number, but I’ve never seen any with laser marking on the body either. That screams knock off to me

arrickburke · Sep 19, 2026

Ya i haven't had the time to take them out so check for more numbers. But I have a picture of a different angle that says they are cheap Bosch 19lb ones. Going to try them since they are on the car. Thanks everyone for the help! New to the mustang world and very excited to get her back up amd running.

Injector question

arrickburke

Member

Attachments

LILCBRA

I wish I didn't have all of these balls in the air

Bullitt347

I have been doing it wrong this whole time

rednotch

I'd like to remain having one chocolate starfish

arrickburke

Member

AeroCoupe

lube between the nut and the face. I know my lubes

DadLife0724

I vote for a new bung hole.

arrickburke

Member

Qtrhrse23

Active Member

manicmechanic007

Mustang5L5

That is…until I whipped out my Bissell

arrickburke

Member

Similar threads

Injector question

Member

Attachments

I wish I didn't have all of these balls in the air

I have been doing it wrong this whole time

I'd like to remain having one chocolate starfish

Member

lube between the nut and the face. I know my lubes

I vote for a new bung hole.

Member

Active Member

That is…until I whipped out my Bissell

Member

Similar threads

Privacy & Transparency

Privacy & Transparency