• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Installing my distributor...

  • Thread starter Thread starter FordRacing302
  • Start date Start date Oct 8, 2005

FordRacing302

5 Year Member
Oct 1, 2005
384
42
59
Cleveland, TN
Oct 8, 2005
#1
  • Oct 8, 2005
  • #1
Well I went to install my distributor for my car and it doesnt seem to want to go all the way in.....I set it at TDC on the #1 cylinder on power stroke, and then went to slide it in and it wont go all the way down, I can feel where the gear meshes with the other gear but I think its not dropping onto the oil pump rod....I looked down in there with a flashlight and the rod is resting on the side and not standing straight up, and when I try to straighten it with a screwdriver it just falls back....Is there any tips or tricks I can use to put this thing in without resorting to a hammer??????
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Oct 8, 2005
#2
  • Oct 8, 2005
  • #2
This might be easy or it might be hard....

On a 302, the oil pump drive shaft is 5/16 hex, so you can rotate it with a 5/16 socket on a long extension. I usually duct tape the socket to the extension so it does not fall off in there.

That will allow you to realign the shaft to better fit into the dist most of the time.

You can also set the dist in there, and rotate the engine over with a big wrench on the crank bolt.

In this case, I would make sure the shaft is still sitting in the oil pump drive before trying to do anything else. There is supposed to be a snap on collar that keeps the shaft from being pulled upward. Works fine without it, but its best if it is there.
 

FordRacing302

5 Year Member
Oct 1, 2005
384
42
59
Cleveland, TN
Oct 8, 2005
#3
  • Oct 8, 2005
  • #3
Thanks for the advice...rotating it sounds like a good idea, Ill go mess around with it now
 

FordRacing302

5 Year Member
Oct 1, 2005
384
42
59
Cleveland, TN
Oct 8, 2005
#4
  • Oct 8, 2005
  • #4
Im still having alot of problems with it...I put a dab of grease in there to keep it centered but it still wont seat down onto it....Anyone else have a better idea?? maybe I should turn the engine over with the starter????
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 9, 2005
#5
  • Oct 9, 2005
  • #5
rd said:
This might be easy or it might be hard....

On a 302, the oil pump drive shaft is 5/16 hex, so you can rotate it with a 5/16 socket on a long extension. I usually duct tape the socket to the extension so it does not fall off in there.

That will allow you to realign the shaft to better fit into the dist most of the time.
Click to expand...
The last tine I did it, I used a 1/4" socket. Be patient, it will fit.
 

FordRacing302

5 Year Member
Oct 1, 2005
384
42
59
Cleveland, TN
Oct 9, 2005
#6
  • Oct 9, 2005
  • #6
Im really stumped as to what to do...Ive stuck alot of bearing grease down there and its standing straight up, Ive used a breaker bar to turn the engine over while I shook the distributor, I had someone else shake the distributor while I bumped the engien over a few times AND it still wont go in??? Im bout to give up and just sell the car................Is there ANYTHING else that I could try??
 

TrophyHead

15 Year Member
Mar 18, 2003
1,195
11
49
PA
Oct 9, 2005
#7
  • Oct 9, 2005
  • #7
Did you get a new distributor or did you replace the hall effect sensor?
 

FordRacing302

5 Year Member
Oct 1, 2005
384
42
59
Cleveland, TN
Oct 9, 2005
#8
  • Oct 9, 2005
  • #8
I finally got it in, I just pulled to oil drive shaft out with a magnet and put it in the bottom of the distributor and then it dropped right in.....But after I got it all wired up I proceeded to wire the coil up and I think I fried the starter , Oh well thanks for your help guys
 
You must log in or register to reply here.

Similar threads

Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
347
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
395
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
C
Shifter lever arm issue
  • chris1993
  • Jan 18, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
274
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 24, 2026
Rcdgl
R
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
480
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
C
Drivetrain T-5 transmission issue
  • Ch3No2
  • Jul 11, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
493
Fox 5.0 Mustang Tech Jul 18, 2025
2000xp8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?