• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

is this hard on new engine

  • Thread starter Thread starter dadiesel5
  • Start date Start date Apr 22, 2007
D

dadiesel5

New Member
Mar 23, 2007
31
0
0
Apr 22, 2007
#1
  • Apr 22, 2007
  • #1
i finally got to drive my car tonight with the fresh rebuilt engine and the car has probably about 40 min of run time just idling at diffrent rpms and when i took the car out tonight i just had to see what it had so i got on it pretty hard taching it up to about 5 to 5500 rpm a couple of times but then started taking it easy on the motor and plan on taking it easy for around 500 miles, do you think i could have hurt my motor by doing this.
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Apr 22, 2007
#2
  • Apr 22, 2007
  • #2
Everyone does that when they really should be taking it easy on the car. I'm sure you didn't hurt it. Dont forget to change the oil after 500 miles.
 

90mustangGT

I felt sorry for girls because
Founding Member
Jan 15, 2002
2,773
17
89
Dallas, GA
Apr 22, 2007
#3
  • Apr 22, 2007
  • #3
Actually, it's good for it but keep the rpm's lower. It helps seat the rings.
 

Mustang78

New Member
Feb 8, 2006
486
0
0
Aberdeen, WA
Apr 22, 2007
#4
  • Apr 22, 2007
  • #4
in the first 20min of runtime on my buddy's old 454 BBC he took it to 6500 RPM's on the back road behind th emuffler shop, that motor obviousely has long since gone POOF, with a flat cam(starved of oil and never broken in)

~Mark~
 
D

dtlionsfan

Member
Nov 12, 2005
83
0
16
Apr 22, 2007
#5
  • Apr 22, 2007
  • #5
Probably not depending on rings.Roller motors and moly rings have pretty much made a "break-in" procedure a thing of the past.My race motors always got a few warm ups and leak checks before hitting 7800 at the track,never had a failure.I change the oil after warming up twice and then at 500 miles.
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
Apr 22, 2007
#6
  • Apr 22, 2007
  • #6
your supposed to do that every now and then. its proper break in procedure. Look it up.
 
D

dadiesel5

New Member
Mar 23, 2007
31
0
0
Apr 22, 2007
#7
  • Apr 22, 2007
  • #7
one more thing i've been having some header glowing issues and played with the timing till i got it up to around 18 or 19*and it took the glow out except for the driver side header this is at about 1600 rpm idle and when i back it down to 900rpm it goes away and also when i drove it i would get out and check it and it was not red but when i'm driving it and when i push the clutch coming to a red light it just goes dead and i have to restart it. what could be causing this. my cam was not degreed he just lined the dots up on the gears. thanks for your help.
 
T

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
Apr 22, 2007
#8
  • Apr 22, 2007
  • #8
you need to create a sig telling the year of the car and the mods to the engine, is it carbed, etc?

If it's idling at 1600 rpm, that might be part of your problem. A stock Fuel Injected 5.0 idles around 650 rpm
 

Foxfan88

My Grandpa has great wood.
Sep 13, 2004
2,487
4
0
Miami, Ok
Apr 22, 2007
#9
  • Apr 22, 2007
  • #9
when i fired my rebuilt engine up i used to old method of going out on the backroads and GETTING ON IT, 2nd gear went from 20-55 and let off and let the car decelerate on the rpms pulls alot of vaccum and keeps the engine well lubed. i did this about 10-12 times

no problems from my engine

i like to think of it this way.

if something in a new engine is going to break its going to do it within a minute or two after start up. it most likely wont just suddenly blow up 2k miles later

there are countless methods on what to do with a new engine.

and 99% of engines come out alright so imo it doesnt really matter.

only thing i would definatle avoid is cruising on the highway at a constant rpm for very long, vary your rpm take it up take it down. dont let it sit i one spot for long for the first 500 miles.
 
D

Dave2000GT

Active Member
Oct 3, 2005
229
26
39
Seattle
Apr 22, 2007
#10
  • Apr 22, 2007
  • #10
I think for break in you are suppossed to go up and down the rev range, but keep it safe like below 5000 rpm. Running a constant low rev will not break it in properly.
 

86nu

New Member
Jan 6, 2007
94
1
0
Birmingham, Al
Apr 22, 2007
#11
  • Apr 22, 2007
  • #11
The motors we build in our shop, we break them in how they are going to be driven.

The first 10-15 for the cam shaft to break in, but after that its balls out on them

We have yet to have a motor come apart, other than fatigue/wear on stuff that doesnt last for ever
 
D

dadiesel5

New Member
Mar 23, 2007
31
0
0
Apr 22, 2007
#12
  • Apr 22, 2007
  • #12
the car a 1993 5.0 just rebuilt with stock rods and crank new forged trw piston trickflow h/c/i 65mm throttle body stock fuel pump stock injectors stock regulator, do any of you have any idea about the header issue and the problem with the car going dead when coming to a stop.
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Apr 22, 2007
#13
  • Apr 22, 2007
  • #13
I believe the header issue might be some unburned fuel making it into your header manifold tube...keep playing with the timing.

As for your break-in, I'm quite sure it is fine. Bringing the revs up and then letting it engine brake increases cylinder pressure/heat and therefore ring seating. But as stated, probably didn't have to go that far up in the revs, but I'm sure it is okay.

I changed my oil 3 times before 500 miles. The first was the 'dirtiest'...with all the lube mixed up in the oil.
 
You must log in or register to reply here.

Similar threads

Strange timing issue
  • 92 Bimini Blue
  • Sep 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
22
Views
739
Fox 5.0 Mustang Tech Oct 20, 2026
rednotch
Ford truck engine swap issues
  • keel
  • Jul 7, 2026
  • Other Auto Tech
Replies
17
Views
785
Other Auto Tech Jul 13, 2026
General karthief
L
Engine 85 GT Excessive Idle
  • lutzkecj
  • Sep 18, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
380
Fox 5.0 Mustang Tech Sep 21, 2026
86HO5.0
8
P
Fuel New Eldebrock 1406 problems 1985 GT 5.0
  • Paddyman
  • Oct 22, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
183
Fox 5.0 Mustang Tech Nov 2, 2026
manicmechanic007
B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?