Engine Is this vacuum line hose clamp normal?

ReefBlueGT · Dec 23, 2020

While examining my engine bay before I go to the trouble of a vacuum and smoke test, I came across this on the line from the upper intake to the charcoal canister. There’s some kind of union piece where the lines meet, with a hose clamp on the end nearest the intake. I gave it a small tug and it wasn’t loose, but wondering if this is normal, or if it indicates a repair, possibly a half-ass one, was done at some point instead of just replacing the whole line...

KRUISR · Dec 23, 2020

I think it is a repair. If I recall correctly, it is a single hose from cannister solenoid to intake.

Mustang5L5 · Dec 23, 2020

Repair.

just replace entire line, although the clamp should still do the trick

ReefBlueGT · Dec 24, 2020

Thanks, going to replace for sure, and see if I find anything else suspect.

Dan02gt · Dec 24, 2020

There should be a coupler at that location. It allows you to remove the upper intake without having to dig under it to disconnect the vacuum line. The hose clamp is not normal though.

ReefBlueGT · Dec 26, 2020

Interesting. So possibly the coupler broke and they used something else with the hose clamp for added strength. In a stock setup, is that coupler one of the typical vacuum fittings found elsewhere in the engine bay?

General karthief · Dec 26, 2020

I can't think of anyplace that has a hose coupler for vac lines like that, oh maybe the vac line for the cruise control line?

ReefBlueGT · Dec 26, 2020

Was thinking of some of the connections on the RH side of the bay, like the white nylon couplers/tees on some of the emissions or AC lines. Can’t wait to get my smoke machine hooked up and see what all is leaking.

Dan02gt · Dec 27, 2020

ReefBlueGT said:
Interesting. So possibly the coupler broke and they used something else with the hose clamp for added strength. In a stock setup, is that coupler one of the typical vacuum fittings found elsewhere in the engine bay?

Yes it is normal to have one there. I recall seeing any other vacuum couplers in the engine bay. The vacuum port that hose connects to is a pain to get to on the bottom of the intake. Ford didn’t want to have someone fiddling under the intake trying to connect it when they installed the engine in the car so they added a coupler there to speed up the process. It’s been on every stock fox body I’ve ever seen and really helps removing and reinstalling the upper intake.

I would get new vacuum hose and a new coupler and replace it. The fuel vapors are rough on that hose and probably why it needed repair.

ReefBlueGT · Dec 27, 2020

I took a closer look at it yesterday, removed the clamp, and took apart the hoses where they meet. There was a long, barbed connector inside, doubt its leaking. But there was some residue on the bottom side of the hose, I think from a small coolant leak off the heater tubes near there. What I didn’t like is that the hose was laying right on top of the engine block. That’s a lot of heat. So when I hooked it back up I at least got it up off there for now.

Monkeybutt2000 · Dec 27, 2020

Dan02gt said:
There should be a coupler at that location. It allows you to remove the upper intake without having to dig under it to disconnect the vacuum line. The hose clamp is not normal though.

It's for the charcoal canister.

Engine Is this vacuum line hose clamp normal?

ReefBlueGT

KRUISR

Mustang5L5

That is…until I whipped out my Bissell

ReefBlueGT

Dan02gt

mazing how much gas smell came from that tiny hole

ReefBlueGT

General karthief

wonder how much it would cost to ship you a pair

ReefBlueGT

Dan02gt

mazing how much gas smell came from that tiny hole

ReefBlueGT

Monkeybutt2000

Mustang Master

Similar threads

Engine Is this vacuum line hose clamp normal?

That is…until I whipped out my Bissell

mazing how much gas smell came from that tiny hole

wonder how much it would cost to ship you a pair

mazing how much gas smell came from that tiny hole

Mustang Master

Similar threads

Privacy & Transparency

Privacy & Transparency