• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

Launching??

  • Thread starter Thread starter 00Perf RedStang
  • Start date Start date Mar 13, 2004

00Perf RedStang

New Member
Mar 13, 2004
28
0
0
Mar 13, 2004
#1
  • Mar 13, 2004
  • #1
What are your suggestions for launching?? I have 00 GT, with BBK Cold Air and a Steeda short throw, im sittin on Nitto 555 275/40/17s. Any suggestions would be a great help, thanks.
 

RageStangX

New Member
Feb 14, 2004
84
0
0
Franklinville,NJ
Mar 13, 2004
#2
  • Mar 13, 2004
  • #2
You could try to launch around 1500rpm and feathering out the clutch to limit wheel spin
 

White Stang

Member
Feb 11, 2004
467
0
16
Ft Lauderdale
Mar 13, 2004
#3
  • Mar 13, 2004
  • #3
If you have Nitto 555Drag radials you should heat them up and I would try launching at about 2000 and take it up each time until they spin and then go back to the rpm's where you were able to get a good launch with no slipping and hopping.
 

00Perf RedStang

New Member
Mar 13, 2004
28
0
0
Mar 13, 2004
#4
  • Mar 13, 2004
  • #4
I have the 555 Extremes, not the drag radials. I probably should have bought the drag radials, but I do a lot of highway driving, so i figured they wouldnt last as long.
 

White Stang

Member
Feb 11, 2004
467
0
16
Ft Lauderdale
Mar 13, 2004
#5
  • Mar 13, 2004
  • #5
I just ordered the 315 drags for the back and when my fronts go I will probally go with extremes in the front. My brother has a foxbody with the drags in the back and it is his daily driver and he says they grip rain or shine
 

daver01

Founding Member
Oct 4, 2002
396
0
0
Lexington, Ky
Mar 13, 2004
#6
  • Mar 13, 2004
  • #6
i'll tell u how not to launch. around 3 grand and dump the clutch. thats good for about a 16 sec run. my best run was almost 1000-1200 rpm easing the clutch out. still learning though. it's tough.
 
You must log in or register to reply here.

Similar threads

I
Engine Help requested in identifying how to resolve engine light issue
  • Ianslaney
  • Oct 4, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
124
SN95 4.6L Mustang Tech Oct 4, 2026
Bullitt347
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
241
SN95 4.6L Mustang Tech Tuesday at 10:14 PM
DangStitches
D
F
Engine 1988 Foxbody idle issues
  • fernandosgarage55
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
26
Views
910
Fox 5.0 Mustang Tech Apr 30, 2026
AeroCoupe
Front Coil Overs and Rear Traditional Springs within a Maximum Motorsports K-Member Kit
  • Habu135
  • Sep 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
24
Views
785
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 9, 2026
Habu135
N
Looking for ECU/CHIP for 1992 5.0
  • Nathan26
  • Sep 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
9
Views
260
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 8, 2026
Qtrhrse23
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?