• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Leaky water pump seal

  • Thread starter Thread starter XenSpidey
  • Start date Start date Apr 16, 2007

XenSpidey

Founding Member
Mar 5, 2001
72
0
0
Apr 16, 2007
#1
  • Apr 16, 2007
  • #1
*Newbie alert*

I noticed the other day i had a puddle of coolant under my car. it was a slow drip and thought it might have been a cracked hose. i looked under the car and the leak appears to be coming from the seal between the water pump and the timing cover. is this something that can just be temporarily patched with RTV, should i take off the water pump and change the gasket, or just replace the water pump. if i take the water pump off how important is it to have the bolts tightened to the right amount of torque.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Apr 16, 2007
#2
  • Apr 16, 2007
  • #2
Putting RTV on a leak that is from a presuurized system does no good. Be prepared to replace the pump gasket. Look closely to make sure the leak isn't coming from the pump shaft seal weep hole.

Some tips when you get ready to replace the pump...

Take a cardboard box, & turn it upside down. Count the number of bolts that hold the water pump on, don’t forget to count the 4 funny looking studs too. Poke a hole in the box for each bolt/stud. Arrange the holes in a circular formation, and mark the box at the 12:00 point. When you remove a water pump bolt, put it in one of the holes in the box according to where it came out of the water pump. When you are done, all bolts will be arranged it the exact same order and position that you removed them from the water pump. That makes re-installing them easy, no wondering where does this bolt go.

A long shank tap should be used to chase the dirt & corrosion out of the original threads before you reassemble everything. Cleaning the threads will help prevent the bolts from seizing next time (yes, there will be a next time).

A word about the links, if they don’t work, do a search on the part number (P/N). MSC updates their catalog regularly, and the pages may change, but the part numbers don’t. You will need the Adobe Acrobat viewer which is also a free download – http://www.adobe.com/products/acrobat/readstep2.html

Long shank 5/16” taps

http://www1.mscdirect.com/CGI/NNPDFF?PMPAGE=267 5/16” pulley tap, 6” shank P/N 04801189 price $18.91

OR second choice, will not clean all the bottom threads unless you grind the end of the tap.

http://www1.mscdirect.com/CGI/NNPDFF?PMPAGE=266 extension tap, 6” reduced diameter shank P/N 04701181 $21.37

Use lots of antiseize on the bolts to protect them from corrosion and make them easier to remove next time.

See http://totallystainless.net/totally.html for replacement stainless steel bolts. Last time I checked, they didn't have the studs. Nice folks, very into cars of all types. They have all kinds of stainless fasteners for almost every car. The prices are very reasonable, less the $10 for the water pump kit without the studs.


The studs are a Motormite item available at your local Advance Discount auto Parts store.

Motormite Water Pump Stud Kits for Ford, Lincoln and Mercury cars and trucks w/3.8L, 4.6L, 5.0L, 5.8L.



Part Number: 23744
 

XenSpidey

Founding Member
Mar 5, 2001
72
0
0
Apr 17, 2007
#3
  • Apr 17, 2007
  • #3
thanks, i'll give that a try one of these nights when i have time, i'm pretty sureit's not a weep hole. i can see a hole on the front of the water pump and it's not coming from that (assuming that's the weep hole).

another thing. when the car's running it doesn't seem to drip out any faster then with the car off. does that mean anything?
 

bloopbloob

Member
Sep 27, 2006
578
4
16
Alberta
Apr 17, 2007
#4
  • Apr 17, 2007
  • #4
i had a similar issue. i'd say if youre going to do all the work to change the gasket, thow a new water pump on there. they're cheap (like $40), and are pretty much a consumable on a 5.0. Even if its ok now, you will be replacing it in the future.... and you won't have to do it twice if it wasnt just a gasket leak...
 
8

89 Saleen#455

Founding Member
Dec 29, 1999
519
5
39
New England
Apr 18, 2007
#5
  • Apr 18, 2007
  • #5
The waterpump replacement is pretty straightforward. Removing the old pump without snapping any of the bolts or studs is the biggest challenge. Try heating the bolts and studs and then soaking them with PB Blaster the night before removing the waterpump. Breaking a bolt or stud will add 2-3 hours to this project. Take your time. Clean and chase threads. Use plenty of Anti-Sieze. Torque the bolts to spec.
 

XenSpidey

Founding Member
Mar 5, 2001
72
0
0
Apr 18, 2007
#6
  • Apr 18, 2007
  • #6
thanks guys! It looks like ill be replacing the water pump. it'll have to wait a week or two though. money's a little tight, and i have to find a torque wrench (i'm going to need one in the future anyways mine as well just buy one) although last night i was looking at it and the leak appears to be near the top left of the water pump. i can see a little "shelf" that has a little puddle on it. but i figure you are right about just replacing it and be done with it. thanks again guys
 
F

ford1288

New Member
Mar 26, 2007
1
0
0
Apr 18, 2007
#7
  • Apr 18, 2007
  • #7
I know the little "Shelf" you are talking about, had the same leak on my car. Upgraded to an Edelbrock Pump, looks like the new gasket sealed the deal. Good luck.
 

XenSpidey

Founding Member
Mar 5, 2001
72
0
0
Apr 18, 2007
#8
  • Apr 18, 2007
  • #8
Ok... riddle me this guys.

so she's been dripping for like 4 days straight in my drive way. today i decide to drive her to work. brought plenty of coolant and water just in case. i filled up the reservoir last night, and ran it for a few minutes and it never drained into the radiator. On the way to work my temp gauge just starts skyrocketing and then suddenly goes back down. maybe the thermostat was stuck and then suddenly kicked in? but i just checked her at lunch and no puddle at all, not leaking a drop... any ideas what would cause that?
 
You must log in or register to reply here.

Similar threads

K
86 GT Water Pump
  • Kade5114
  • May 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
228
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 11, 2026
nickyb
M
2001 v6 heater return pipe leak question
  • mnky99
  • Nov 11, 2025
  • SN95 V6 Mustang Tech
Replies
1
Views
395
SN95 V6 Mustang Tech Nov 11, 2025
mnky99
M
B
water pump installation questions
  • B0udreaux
  • Feb 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
38
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 28, 2026
General karthief
Crack in Water Pump
  • 93gtmustang
  • Oct 8, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
29
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 27, 2024
General karthief
B
2001 SVT Cobra Overheating Issue
  • bradencaron0
  • May 8, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
284
1996 - 2004 SN95 Mustang -General/Talk- May 8, 2025
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?