• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-

Lets talk roll bars and cages

  • Thread starter Thread starter midnightdriver
  • Start date Start date Apr 10, 2010

midnightdriver

Active Member
Jan 3, 2010
443
2
27
Northern California
Apr 10, 2010
#1
  • Apr 10, 2010
  • #1
I did a search and could not find what I was really looking for, sry if I missed one.

I want to use my 2000 gt to do some auto cross, road racing and open road racing. I have checked out Maximum Motorsports and autopower cages. I like the 4 point MM with the 5 point harness location but I am torn about losing the back seat. I mean people do sit back there but rarely, I mean since the the car was new (2000) probably 30 times. But I don't want to cut off that option. I like the autopower full bolt in cage too, but once again 90% of driving is on the street. I don't mind having the race car look just don't want the race car annoyances.

Plus, with a 5 point harness would I have to change my seats of could I still you the factory seats?

Please state what you would do

Thanks
 

midnightdriver

Active Member
Jan 3, 2010
443
2
27
Northern California
Apr 11, 2010
#2
  • Apr 11, 2010
  • #2
Anyone?

I find it hard to believe that not one of you have a roll bar or roll cage in your car or even though about it.
 

crazystang25

Member
Jan 25, 2009
492
0
16
Apr 11, 2010
#3
  • Apr 11, 2010
  • #3
midnightdriver said:
I did a search and could not find what I was really looking for, sry if I missed one.

I want to use my 2000 gt to do some auto cross, road racing and open road racing. I have checked out Maximum Motorsports and autopower cages. I like the 4 point MM with the 5 point harness location but I am torn about losing the back seat. I mean people do sit back there but rarely, I mean since the the car was new (2000) probably 30 times. But I don't want to cut off that option. I like the autopower full bolt in cage too, but once again 90% of driving is on the street. I don't mind having the race car look just don't want the race car annoyances.

Plus, with a 5 point harness would I have to change my seats of could I still you the factory seats?

Please state what you would do


Thanks
Click to expand...

well i have already lost my rear seat, and if i was doing one i would be building it myself. but basically it comes down to whether or not you want to lose your rear seat. i have seen some cars that have managed to keep their back seats after a cage install, but the one i know specifically had a custom cage in it. me personally i dont like cages or roll bars in street driven cars because of some of the things i have seen. your neck can stretch several inches before any damage and that could cause your head to contact the main hoop which is a bad day. thats the reason nhra and scca require that any tubing within a certain distance from any body part be padded. i know of one bad one where the guy rolled his miata and his head contacted the main hoop, needless to say he didnt make it. only way im doing a cage or roll bar is if i am wearin a helmet in that car at all times.
 

midnightdriver

Active Member
Jan 3, 2010
443
2
27
Northern California
Apr 11, 2010
#4
  • Apr 11, 2010
  • #4
crazystang25 said:
well i have already lost my rear seat, and if i was doing one i would be building it myself. but basically it comes down to whether or not you want to lose your rear seat. i have seen some cars that have managed to keep their back seats after a cage install, but the one i know specifically had a custom cage in it. me personally i dont like cages or roll bars in street driven cars because of some of the things i have seen. your neck can stretch several inches before any damage and that could cause your head to contact the main hoop which is a bad day. thats the reason nhra and scca require that any tubing within a certain distance from any body part be padded. i know of one bad one where the guy rolled his miata and his head contacted the main hoop, needless to say he didnt make it. only way im doing a cage or roll bar is if i am wearin a helmet in that car at all times.
Click to expand...

Well thanks for the info, that would definitely hurt but I plan on padding the entire roll bar and the nice thing about the MM roll bar is its hoop is located behind the seat, so that head/bar interference is minimized.

I have to say though, I have driven in many cj5, cj7, and xj's with roll bars (came close to rolling a few off road, not being stupid just tough trails). And after a friend of mine fell asleep at the wheel in his cj5 and rolled and estimated 30 times (he was going 75mph on the freeway) and walked a way with only glass scratches and a bent roll bar. I see there purpose, if properly set up, for a street car.

If I do install the bar, I plan on installing 5 point belts along with corbeau race seats to also reduce the head/roll bar issue but like you said, a helmet would be the best.

Thanks
 

Tim2002GT

Founding Member
Apr 10, 2002
635
4
29
Tulsa, Oklahoma
Apr 11, 2010
#5
  • Apr 11, 2010
  • #5
If and when I do a cage I will probably get a weld-in 6 pt from Wolfe Race Craft - Home Page. Here's the one I am looking at...

Mild steel
Wolfe Race Craft - Detail
Chromoly
Wolfe Race Craft - Detail

I personally would never use a bolt-in rollbar. Not strong enough for its purpose, IMO.
 

crazystang25

Member
Jan 25, 2009
492
0
16
Apr 11, 2010
#6
  • Apr 11, 2010
  • #6
Tim2002GT said:
If and when I do a cage I will probably get a weld-in 6 pt from Wolfe Race Craft - Home Page. Here's the one I am looking at...

Mild steel
Wolfe Race Craft - Detail
Chromoly
Wolfe Race Craft - Detail

I personally would never use a bolt-in rollbar. Not strong enough for its purpose, IMO.
Click to expand...

I agree if you do put one in then it should be welded in. Of course that right there will be fun since the whole car is galvanized. I figured that out when I was building my suspension. There is a lot of sanding to do for prep work. I also found that heating the area with a oxy-acetylene torch works well for removing it on area's you cant see, since it will flake on as the metal turns red hot.
 

Night Shifter

Well-Known Member
Dec 24, 2005
1,710
27
59
Daytona
Apr 11, 2010
#7
  • Apr 11, 2010
  • #7
loose the rear seats...theres not gonna be a single person that will want to sit in the back seat with a bar in there face..

with that said, unless youre going for an all out open track car, save your money and do like i did and buy a harness bar and harnesses and you can either buy racing seats or keep the stock ones like i did



 

midnightdriver

Active Member
Jan 3, 2010
443
2
27
Northern California
Apr 11, 2010
#8
  • Apr 11, 2010
  • #8
Night Shifter said:
loose the rear seats...theres not gonna be a single person that will want to sit in the back seat with a bar in there face..

with that said, unless youre going for an all out open track car, save your money and do like i did and buy a harness bar and harnesses and you can either buy racing seats or keep the stock ones like i did
Click to expand...

Hmm, that looks sweet but is it still somewhat easy to get into the back? I also though with a harness bar you had to run a roll bar because your neck could get crushed in a roll over because you cant move out of the way?

This is the race I want to prep my car for and would love to bring more of you on board. I probably won't make it this year though.

Index of Rules, Regs, Requirements and Specs!
 

Night Shifter

Well-Known Member
Dec 24, 2005
1,710
27
59
Daytona
Apr 11, 2010
#9
  • Apr 11, 2010
  • #9
yeah theres tons of room in the back with the harness bar...just a rod on each side running from the bar to the floor that you have to move around to get in but no worse than if you had a cage back there...

never hear the whole neck crush thing but i see your point lol
 
You must log in or register to reply here.

Similar threads

F
Ford 460 swap
  • Ford460
  • Sep 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
503
1996 - 2004 SN95 Mustang -General/Talk- Sep 14, 2026
Ford460
F
Alternator not charging
  • SchwarzStock
  • Jul 6, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
3
Views
269
1965 - 1973 Classic Mustangs -General/Talk- Oct 17, 2026
SchwarzStock
Progress Thread 91GTstroked 90 7 up convertible build
  • 91GTstroked
  • Apr 18, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
488
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 22, 2026
91GTstroked
2
Resolved Electrical mayhem
  • 2000ElectricGreen
  • Mar 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
498
1996 - 2004 SN95 Mustang -General/Talk- Sep 4, 2026
2000ElectricGreen
2
0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
1K
1996 - 2004 SN95 Mustang -General/Talk- Oct 7, 2026
2v_johnny
2
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?