• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Lifters??

  • Thread starter Thread starter asecretfile
  • Start date Start date Apr 21, 2008

asecretfile

New Member
Feb 11, 2007
228
0
0
Apr 21, 2008
#1
  • Apr 21, 2008
  • #1
Doing a cam swap on my 87GT to a tfs 1 and was wondering if its essential that I replace the lifters...the ones I took out look fine and a new set is like 130 bucks for the FRPP but if I have to I have to

thanks
 

mustangfan1990

New Member
Jul 17, 2005
505
1
0
Lenoir, North Carolina
Apr 21, 2008
#2
  • Apr 21, 2008
  • #2
asecretfile said:
Doing a cam swap on my 87GT to a tfs 1 and was wondering if its essential that I replace the lifters...the ones I took out look fine and a new set is like 130 bucks for the FRPP but if I have to I have to

thanks
Click to expand...

I wouldnt say you have to if you didnt have problems with the ones before. Those lifters dont go bad often. I would though anyway since you have them out considering if they are stock then they prolly need it and you take away a chance of having problems sooner than later...IMO
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Apr 21, 2008
#3
  • Apr 21, 2008
  • #3
they are roller lifters. you should be good to go. they dont wear out like the flat hydraulic lifters.
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Apr 21, 2008
#4
  • Apr 21, 2008
  • #4
If I have factory valve covers will I need to get taller valve covers for that cam?

thanks
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Apr 21, 2008
#5
  • Apr 21, 2008
  • #5
Keeping your stock lifters? I know a lot of guys pick up the Fox valve covers because they have more clearance. Even with some good size roller rockers, you can usually keep them, if you remove the baffle inside.
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Apr 21, 2008
#6
  • Apr 21, 2008
  • #6
your valve covers will be fine unless you switch to roller rockers, then like said earlier you will have to grind out the oil baffle.
 
You must log in or register to reply here.

Similar threads

H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
614
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
K
Resolved Need some assistance. Holley Terminator X alongside H/C/I. Very rough/inconsistent idle
  • karhoot
  • Jun 6, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
236
Fox 5.0 Mustang Tech Jun 6, 2026
karhoot
K
G
Engine Pushrod Length Question
  • germain101
  • Sep 22, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
745
Fox 5.0 Mustang Tech Sep 25, 2025
Noobz347
P
Fuel New Eldebrock 1406 problems 1985 GT 5.0
  • Paddyman
  • Oct 22, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
173
Fox 5.0 Mustang Tech Nov 2, 2026
manicmechanic007
C
347 advice
  • CRonaldo773
  • Jan 27, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
370
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 28, 2026
2000xp8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?