• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Lower Manifold Removal

  • Thread starter Thread starter 95GTV8
  • Start date Start date Sep 24, 2005

95GTV8

New Member
Jul 25, 2005
386
3
0
Washington State
Sep 24, 2005
#1
  • Sep 24, 2005
  • #1
ok, i tried to remove my stock lower today and i ran into some problems. I got to the lower, removed injectors etc. But on the front left side near the thermostat housing their is a bolt that comes up and connects into 2 places, one to the side almost perpindicular, and then it connects to a metal pipe which in turn connects to two hoses running into the firewall. The hole where this bolt goes, also goes into the thermostat housing chamber, so im thinking it's possible the heater line? I tried to turn this bolt but it wouldn't turn anymore, and it seemd as if the metal pipe was holding it down so it couldn't be turned upwards anymore. My instructions never mentioned anything about this, but i could not find any way to get this thing off of the lower intake. Can anybody help me? It's a real pain in the ass having my stang stuck w/ no intake on it and not be able to drive it.
 

legalize420

Active Member
May 21, 2005
1,541
1
37
South Florida
Sep 24, 2005
#2
  • Sep 24, 2005
  • #2
you did drain the coolant right? if so go ahead and take the hoses off the front and back of the tube. after all 4 are off you can remove the intake. it will be much easier getting the tube off when the intake comes off.
 

95GTV8

New Member
Jul 25, 2005
386
3
0
Washington State
Sep 24, 2005
#3
  • Sep 24, 2005
  • #3
allright, well where the hoses connnect to the firewall, they put the ****ing clams on upside down so it's near impossible to get them off. But i'll just take the clamps off tomorrow and then take the lower intake off.
 

95GTV8

New Member
Jul 25, 2005
386
3
0
Washington State
Sep 25, 2005
#4
  • Sep 25, 2005
  • #4
any more opionions? i'll try and finish the job off tomorrow.
 
You must log in or register to reply here.

Similar threads

Resolved 1999 cobra removed lower intake manifold to crossovertube
  • hvcobra99
  • Sep 6, 2026
  • SVT Tech Forum
Replies
0
Views
166
SVT Tech Forum Sep 6, 2026
hvcobra99
Engine Retorque lower intake manifold bolts
  • 91GTstroked
  • Sep 8, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
407
Fox 5.0 Mustang Tech Sep 8, 2025
Noobz347
Engine New factory manifold no start
  • Fishnchips
  • Oct 15, 2026
  • 1994 - 1995 Specific Tech
Replies
13
Views
394
1994 - 1995 Specific Tech Oct 22, 2026
DadLife0724
Engine Re-torquing intake manifold bolts question
  • 91GTstroked
  • Feb 22, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
1K
Fox 5.0 Mustang Tech Mar 1, 2025
Jarhead67
J
Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
347
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?