MAF help

jonbacon · Sep 12, 2011

So, I just got a 92gt.. I have replaced the idle air,MSF,TPS,Fuel filter.
car runs ok when the MAF is unhooked. when I plug it back in, it will cut off and idle like crap..its throwing the 081 063 066 082 codes... I was told its bad injectors.. can anyone help... I have had to advance the timing a little to maintian a half way descent idle..
other than thart car ran great..just started idlin gbad ne morning, have been replaceing parts every since. cant quite figure out what it is..

Fabbed4d88 · Sep 12, 2011

Is the MAF new? Have you tried cleaning it wit MAF cleaner?

jonbacon · Sep 12, 2011

yeh sorry, has a new maf..i cant hook it up ..it will cause the stang to have a very rough idle around 500 rpms then just cut out..if i leave it in and try to crank it, it may crank and still run bad ans cut out , but cant drive it at all

Fabbed4d88 · Sep 12, 2011

Run any different when it's warmed up?

jonbacon · Sep 12, 2011

NO, STILL IDLES BAD WITH THE MAF HOOKED UP... KIND OF HAS A SMALL SKIP TO IT..WHEN WARM.. IF I TRY TO HOOK IT UP AND LET IT IDLE, I HAVE TO HOLD THE GAS.. THEN IT WONT DRIVE GOOD, KIND OF SPUTTERS LIKE THE TPS IS BAD..IM STUMPPED...

Fabbed4d88 · Sep 12, 2011

Did you adjust the TPS after you put the new one on? I know there is a step-by-step on how to do this somewhere in these forums.

Fabbed4d88 · Sep 12, 2011

I would also check for vacume leaks.

jonbacon · Sep 12, 2011

I found 2 leaks, they are all fixed. I put the new tps on, not sure if it needs adjustments. I put it on just like it came off. before it was jumping whiole driving, really bad. replaced fuel filter now its better. but still doesnt idle right or drive right.. was told the coolant tep could also cause this..

Fabbed4d88 · Sep 12, 2011

Possible....if so it's a cheep fix.

jonbacon · Sep 12, 2011

Yeh, im at loss.. not sure where to go from here. i am driving around with the maf unhooked for now. but not sure why it wont run right when i plug it back in...
has new
idle air, maf,tps, plugs.headers, flowmasters.. throwing these codes
081,083,066,063.. whci relate to the egr and injectors. the fuel filter had very dirty brown gas cming out of it when i changed it yesterday.. im gonna clean injectors this weekend. trans kit tomorrow night. just not sure what could be making it drive so bad?

Fabbed4d88 · Sep 12, 2011

If the gas in the filter was brown then there may be a good chance some debris may have got into the injectors. How long did the car sit before you picked it up?

jonbacon · Sep 12, 2011

a couple of years..they may have drove it for a mile or 2. i got it drove it for a few days, right after the hurricane, i went to crank it uop and it had a very rough idle around 400-600rpms, so went through the maf,idle,tps,plugs. still cant hook the maf up even though its new.. it will cut off. i havent tired to let it idle withth it hooked up. chanegd the filter for fuel and it cleared up the jumping while driving, but not all the way. so i was told it could be coolant temp sensor, then one guy tells me my injectors are clogged up. ran some seafoam throug it this sunday. but havent realy driven it a lot .. just to work and back..

stykthyn · Sep 12, 2011

If your injectors are truly fouled seafoam isn't going to get them clean.

jonbacon · Sep 12, 2011

yeh, just not sure if thats the problem. but im sure its a big part of it. would that cause the maf to not run right??

stykthyn · Sep 12, 2011

jonbacon · Sep 12, 2011

lol, any ideas??? at this point man i need any advice i can get....im good with paint and body work, hell even building a motor but this is a new issue for me.. i cant find any leaks just not sure why maf isnt working correctly

Fabbed4d88 · Sep 12, 2011

Best bet for that would be to pull the injectors out and have the professionally cleaned. If indeed it is the injectors it would probably be wise to clean the tank and blow out the lines..

jonbacon · Sep 12, 2011

at this point im trying to figure out why when the maf is plugged back up it wants to stall out.. its new along withthe other parts

stykthyn · Sep 12, 2011

Last time I had that issue it was vacuum related. Go to the tech forum and go through the surging idle check list. Lots of good info in there.

jrichker · Sep 13, 2011

See the "Surging Idle Checklist for help with all your idle/stall problems.

The quick and easy way to dump the codes is in there too, and all you need to do it is a paper clip! The first two posts contain all the fixes & updates. At last count there were 24 possible causes and fixes for surging idle/stall problems. I continue to update it as more people post fixes or ask questions.

MAF help

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

Member

I want to measure mine. It doesn't look that tall.

Member

I want to measure mine. It doesn't look that tall.

Member

Member

Member

I want to measure mine. It doesn't look that tall.

StangNet's favorite TOOL

Similar threads

Privacy & Transparency

Privacy & Transparency