• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

misfire problem?

  • Thread starter Thread starter 88Stangboy
  • Start date Start date Dec 15, 2005
  • 1
  • 2
Next
1 of 2 Next Last

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Dec 15, 2005
#1
  • Dec 15, 2005
  • #1
I tried to search this but the damn search thingy wont work!
Anyways, i've got this re-accuring misfire problem. I've done
just about everything i can think of, checked all the grounds
to the ignition box, engine, etc. Changed coil, all new MSD
wires, new distributor cap, plugs, etc. And it goes away for
a while, then it comes back some times and then goes away.
Its pissing me off very badly, especially when i replaced cap $25,
wires $89, Coil $61, plugs about $30...i've got a Hi-6 ignition box,
i replaced the Crane Cams coil with an MSD, i've also added fuel
injector cleaner and checked the wiring harness to the injectors.
Oh and the distributor is a stock unit, i also replaced the rotor twice.
One time i bent the little metal tab on the rotor up more so it contacted the pickup on the cap that comes from the coil and the misfire went away for a while, then a couple of days later it came back, i tried it again to no avail, What the hell is wrong with this? Am i forgetting something?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Dec 15, 2005
#2
  • Dec 15, 2005
  • #2
Do you have good wire separators?

Good luck.
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Dec 15, 2005
#3
  • Dec 15, 2005
  • #3
Do you know which cylinder is causing the problem? You could dump the codes and run the cylinder balance test to give you an idea of where to look at least... It's better than wasting all that money trying to chase down the problem.

As always, you have the correct 5.0L HO firing order right? A engine can still run OK with crossed wires and not be noticalbe until it's placed under a load.

I had a missing cylinder once: The MSD plug wire was broken in the middle (right out of the box I might add)
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Dec 15, 2005
#4
  • Dec 15, 2005
  • #4
I got the same problem too, did this just happen or just showed up after you did some work on it
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Dec 16, 2005
#5
  • Dec 16, 2005
  • #5
It just showed up one day. I think moisture is getting under the distributor
cap, it happens more when it rains outside. Yes i have wire seperators, i've
pretty much narrowed it down to the distributor, its a stock 5.0 distributor.
I know i have the right firing order, i checked and re-checked that. Made sure i had crossed no wires. I mean sometimes it runs absoblutly fine, others it starts skipping. It will be fine, like for example, i might have not cracked the
hood on the car for a week. In that week it might have came and went three or four times. It seems to run fine, then out of absoblutly no where it starts again. It's so damn annoying . I think im going to take it and have the codes ran like yall suggested. Until than, anymore suggestions?
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Dec 17, 2005
#6
  • Dec 17, 2005
  • #6
run the codes, whats it feel like when its misfiring, how long does it last do u have any power
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Dec 17, 2005
#7
  • Dec 17, 2005
  • #7
87stangdiddle said:
run the codes, whats it feel like when its misfiring, how long does it last do u have any power
Click to expand...


It just kinda jerks and looses power, it still runs nice and smooth, just looses power and it makes that 'puh, puh' sound and when it goes away i got power again. Im starting to think it's got something to do with fuel starvation, cause it'll run fine and then when i get on it it start it for a few seconds then it might go away or it might stay until i let off. Then sometimes ill press my clutch in the go to stop and the engine will die, it starts right back up. Scarred the hell out of me one day, i was going around a corner (About 50mph) and i pressed the clutch in to coast and the engine died and i lost power steering and it jerked torwards the ditch, i cranked that bastard up as quick as i could. I gotta fix this problem.amnit:
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Dec 17, 2005
#8
  • Dec 17, 2005
  • #8
Sounds like it could be the fuel pump to me
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Dec 18, 2005
#9
  • Dec 18, 2005
  • #9
87stangdiddle said:
Sounds like it could be the fuel pump to me
Click to expand...

Yea thats what i was thinking, i've replaced all my injectors about a year ago with 24lb'rs. And the fuel filter was replaced about a year and a half ago.The fuel pump is probabally to small, not sure what size it is. Guess it's true, the fuel system is always the most overlooked on a car.
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Dec 18, 2005
#10
  • Dec 18, 2005
  • #10
87stangdiddle said:
Sounds like it could be the fuel pump to me
Click to expand...

Yea thats what i was thinking, i've replaced all my injectors about a year ago with 24lb'rs. And the fuel filter was replaced about a year and a half ago.The fuel pump is probabally to small, not sure what size it is. Guess it's true, the fuel system is always the most overlooked on a car. Im going to look at the relay first though, don't want to pull the tank out just to find the pumps fine. The guy i got the car from had put in a BBk pump, but like i said, i don't know what size, most likely a 190 or so.
 

bobbys9350

New Member
Mar 30, 2005
472
0
0
Dec 18, 2005
#11
  • Dec 18, 2005
  • #11
$30 for plugs? You wouldnt happen to be running Bosch's or something like that would ya?
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Dec 18, 2005
#12
  • Dec 18, 2005
  • #12
Yea, i wouldn't buy them again, i've not found them to be any better than regular autolites IMO...
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Dec 18, 2005
#13
  • Dec 18, 2005
  • #13
Plat plugs can cause a high speed misfire and lack of power all themselves, for some EFI 5.0L motors.

Good luck.
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Dec 18, 2005
#14
  • Dec 18, 2005
  • #14
Yea i agree, try autolite 25's and see if it cures it, when i got mine the other day came to like 12.50 or something like that
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Dec 18, 2005
#15
  • Dec 18, 2005
  • #15
Ill probabally do that, but right now i got the top end of my engine torn down...i feel like an idiot right about now. I was taking something off my fire wall and i had a damn magnetic tipped screw driver, well my upper intake was off. (see where im getting at?) Well the screw fell off and right down one of the ports, i should have had duct tape over it, but i was just taking a useless screw loose, didn't think i would need to cause i was about to put the intake back on. I tried running a magnet down it...but of course, the valve was open! So....you get the idea, but ill try the spark plugs, i liked the autolites better anyways.
 

timewarped1972

Member
Jun 17, 2004
642
0
16
mesa, az
Dec 19, 2005
#16
  • Dec 19, 2005
  • #16
depending on how big the screw is try one of those telescoping magnets down the spark plug hole first.....you might have to bend the telescoping part up a little but it's worth a shot.
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Dec 19, 2005
#17
  • Dec 19, 2005
  • #17
Ya thats what i did, but i took the valve cover off and the rocker was down on that port, the valve was open. I still fiddled around with it for probabally and hour, hoping and preying it would come out, but nothing. Im just going to take the head off tommorrow. Been working lately so all i've gotten off is the lower manifold, fuel rails, etc. I got some new autolites on the way home from work yesterday. I hope it works. I took a few of the platinum plugs out, none of them are fouled out. But ill keep posting. Thanks for all your help so far.
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Dec 20, 2005
#18
  • Dec 20, 2005
  • #18
I did the same thing once when i had my old motor, ready to put my upper intake on (after doing head gaskets) and I swear a bolt went down one of the intake ports, i swear i heard it the clank and everything, I tried with a flashlight and magnet and couldnt find anything. Took the head to be sure and there was nothing there haha that sucked. From now on I put tape over the ports lol
 

88Stangboy

Banned
Dec 12, 2005
342
0
0
Greenville, SC
Dec 20, 2005
#19
  • Dec 20, 2005
  • #19
I guess i'll finally get the head off sometime this year! Between my girlfriend, job and so on i get about an hour each night to work on it. Then my woman comes out to fetch me from the garage...so i mean, what are you gonna do Oh well. Im in no hurry, my tranny's in the shop and i got my license suspended for reckless driving (and thats how my tranny got broke, dont ask) But thanks for everyone who posted on the misfire question...i guess it's fixed, if not i'll post again with the new set of problems....
 
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Dec 20, 2005
#20
  • Dec 20, 2005
  • #20
As far as the fuel pump goes, just thought I'd add a couple things. When the pump on my 87 starting going out, it had 2 noticable symptoms. First, I would have to turn my key on and off a few times in order to get the car to immediately fire up. Secondly, it would take a dump every time I'd get on it hard. Seemed to idle ok, but always had to drive conservatively. Replaced with a 190 bbk and that totally fixed it.
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

Engine Hiccup at full throttle
  • keel
  • Jun 2, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
31
Views
1K
Fox 5.0 Mustang Tech Jul 30, 2026
keel
K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
397
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
Engine Misfire below 3K RPM
  • foxbodyclark
  • May 25, 2025
  • Fox 5.0 Mustang Tech
Replies
19
Views
1K
Fox 5.0 Mustang Tech May 31, 2025
General karthief
M
Help! 2003 GT misfire when hot
  • Modular03
  • Feb 10, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
620
SN95 4.6L Mustang Tech Feb 13, 2026
Mustang5L5
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
520
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?