• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-

Mod motor Carnage pics!!!

  • Thread starter Thread starter EPIK
  • Start date Start date Nov 17, 2008
  • 1
  • 2
Next
1 of 2 Next Last

EPIK

Member
Jul 3, 2004
796
1
16
LEFT COAST
Nov 17, 2008
#1
  • Nov 17, 2008
  • #1
This is a pic of a Mach 1 motor that had an Eaton Swap. It was an automatic car with the $h!tty cast 6 bolt crank (unlike the manual cars with the 8 bolt Forged Cobra crank), but I doubt that had anything to do with the motors outcome.... I saw this @ AED (advanced engine development) last Saturday, but dont get me wrong, it had nothing to do with any of their work, AED did not build this motor, they are just picking up the pieces.

 

Attachments

  • CIMG3022.webp
    77.3 KB · Views: 237
  • CIMG3021.webp
    63.7 KB · Views: 227

CobraRed_96_GT

Active Member
May 20, 2006
1,421
4
39
UCSD/La Jolla
Nov 17, 2008
#2
  • Nov 17, 2008
  • #2
Yeah, i doubt the 6 bolt crank had anything to do with it as they are good for 600rwhp. Boost at 10:1 compression requires a spot on tune - that looks like the opposite.
 

hotmustang331

Active Member
Apr 29, 2004
2,967
3
48
Bastrop,TX
Nov 17, 2008
#3
  • Nov 17, 2008
  • #3
WOW. Wonder how much boost they were trying to run? It should have been fine @ 8PSI.....but with a crappy tune, anything can happen.
 

EPIK

Member
Jul 3, 2004
796
1
16
LEFT COAST
Nov 17, 2008
#4
  • Nov 17, 2008
  • #4
I think it was a stock pulley? The shop who tuned the car (not AED) has had this car, & an 01 GT with a procharger p1sc (stock bottom end) both blow up in the last few months...
 

mazen189

Member
Jul 31, 2007
424
0
16
I.E. southern california
Nov 17, 2008
#5
  • Nov 17, 2008
  • #5
ha, lovely, well, i know where to NOT go for a tune now.
 

EPIK

Member
Jul 3, 2004
796
1
16
LEFT COAST
Nov 18, 2008
#6
  • Nov 18, 2008
  • #6
mazen189 said:
ha, lovely, well, i know where to NOT go for a tune now.
Click to expand...


AED didnt tune the car or build it BTW, they are just fixing it...
 

clentonz

New Member
Jul 13, 2008
26
0
0
Nov 18, 2008
#7
  • Nov 18, 2008
  • #7
wow, that scared the chit out of me, I thought for a second before I actually read it(looking at the pics), and thought that your motor had blown up!

but that does look bad, I guess that's what you get for using a 6 bolt instead of a 8
 

EPIK

Member
Jul 3, 2004
796
1
16
LEFT COAST
Nov 18, 2008
#8
  • Nov 18, 2008
  • #8
clentonz said:
wow, that scared the chit out of me, I thought for a second before I actually read it(looking at the pics), and thought that your motor had blown up!

but that does look bad, I guess that's what you get for using a 6 bolt instead of a 8
Click to expand...

Thanks for being concerened!!! Im glad its not my motor, thats 4 sure...

Ford screwed the auto Mach 1 owners by giving them the 6 bolt cast GT crank...
 

CobraRed_96_GT

Active Member
May 20, 2006
1,421
4
39
UCSD/La Jolla
Nov 18, 2008
#9
  • Nov 18, 2008
  • #9
EPIK said:
Thanks for being concerened!!! Im glad its not my motor, thats 4 sure...

Ford screwed the auto Mach 1 owners by giving them the 6 bolt cast GT crank...
Click to expand...
Was for using the 6 bolt flex plate that the autos use on all their 01+ cars
 
S

stang06girl

Member
Nov 8, 2008
30
0
6
Southern California
Nov 18, 2008
#10
  • Nov 18, 2008
  • #10
The mains (and the crank from what i could see) look to still be in tact. It looks more like a rod broke, and then the carnage punched a hole in the block afterwards. From what I have read, the rods are the weakest link in the non cobra motors.
 

bhuff30

Founding Member
Dec 11, 2001
6,037
35
129
Olathe KS
Nov 18, 2008
#11
  • Nov 18, 2008
  • #11
Why are is everyone talking about and complaining about the cast crank? The powder cast rod is what obviously let go. The rods and pistons are MUCH weaker than the cast crank, so it doesn't really matter what crank you have if you still have the other stock internals.

Also, I wouldn't blame the tuner immidiately. Even with a very conservative and safe pump gas tune, the rods aren't good for more than 450rwhp. If the car was tuned to make 450rwhp in 80* weather, it is already tuned at the power limits of the rods. I don't know where the car is, but around here it is COLD and my car feels fast again. That same 450hp car may be making 500rwhp in this cold weather, which obviously won't work well with rods that are already at the limit.

In my book, that's what happens when you push the limits of what the factory parts are cabable of. Sometimes you win, sometimes you loose, but your always on the line. Ford's quality control ensures the engine will hold up to 300hp everyday, all day. If they see a flaw or defect in a piston or rod, they don't much care long as it is inside their tolerance which they set for 300hp. Because tolerances are all different, some engines will kick a rod at 420rwhp while other lucky people run 480+rwhp for years without a hitch.
 

hotmustang331

Active Member
Apr 29, 2004
2,967
3
48
Bastrop,TX
Nov 18, 2008
#12
  • Nov 18, 2008
  • #12
EPIK said:
I think it was a stock pulley? The shop who tuned the car (not AED) has had this car, & an 01 GT with a procharger p1sc (stock bottom end) both blow up in the last few months...
Click to expand...

Man either the guy is beating the everliving crap out of it.....or they were both tuned by the same person.
 
D

darkside03gt

Member
Feb 19, 2007
851
8
18
Sacramento CA
Nov 18, 2008
#13
  • Nov 18, 2008
  • #13
So who tuned the car? I have a idea but I'm not gone just throw it out there.
 

Mustang92

SN's #1 1%er
Jun 6, 2001
6,467
2
79
South Florida
Nov 18, 2008
#14
  • Nov 18, 2008
  • #14
stang06girl]The mains (and the crank from what i could see) look to still be in tact. It looks more like a rod broke said:
Why are is everyone talking about and complaining about the cast crank? The powder cast rod is what obviously let go. The rods and pistons are MUCH weaker than the cast crank, so it doesn't really matter what crank you have if you still have the other stock internals.

Also, I wouldn't blame the tuner immidiately. Even with a very conservative and safe pump gas tune, the rods aren't good for more than 450rwhp. If the car was tuned to make 450rwhp in 80* weather, it is already tuned at the power limits of the rods. I don't know where the car is, but around here it is COLD and my car feels fast again. That same 450hp car may be making 500rwhp in this cold weather, which obviously won't work well with rods that are already at the limit.

In my book, that's what happens when you push the limits of what the factory parts are cabable of. Sometimes you win, sometimes you loose, but your always on the line. Ford's quality control ensures the engine will hold up to 300hp everyday, all day. If they see a flaw or defect in a piston or rod, they don't much care long as it is inside their tolerance which they set for 300hp. Because tolerances are all different, some engines will kick a rod at 420rwhp while other lucky people run 480+rwhp for years without a hitch.
Click to expand...

Right on the money the crank had nothing to do with this failure. Rods obviously let go either due to bad detonation that pounded on them or just pushing the limits of the stock rods too far. It sucks it took just about everything out with it. Block is trashed, crank may be salvageable but being cast they would be better off going forged in a power adder 4v car. Hopefully the heads didn't take on any damage.

Bill
 
B

blubullett

Member
Jun 22, 2006
535
6
18
Modesto, CA
Nov 18, 2008
#15
  • Nov 18, 2008
  • #15
darkside03gt said:
So who tuned the car? I have a idea but I'm not gone just throw it out there.
Click to expand...

Me too!! Was it the shop that tuned my car? But if you look around you will find that every shop has blown a motor.
 
D

darkside03gt

Member
Feb 19, 2007
851
8
18
Sacramento CA
Nov 18, 2008
#16
  • Nov 18, 2008
  • #16
blubullett said:
Me too!! Was it the shop that tuned my car? But if you look around you will find that every shop has blown a motor.
Click to expand...

very true. nobody is perfect. However there is one shop in the sacramento area that has a rep for blowing up engines and I would like to know who it is.
 
B

blubullett

Member
Jun 22, 2006
535
6
18
Modesto, CA
Nov 18, 2008
#17
  • Nov 18, 2008
  • #17
Who tuned your car darkside? Mine was tuned by speedfreaks in tracy. It runs great and I have beaten the **** out of it since I got it, but I have sence heard some bad things about them. Actually a lot. But my car is great. Sorry to hijack the thread but you cant show us all of this and then not tell us who did it.
 

blckstng96

Member
Apr 13, 2004
208
0
16
Nov 19, 2008
#18
  • Nov 19, 2008
  • #18
yeah deff had nothing to do with the crank.i have rarely every heard of a crank issue on a 4.6 regardless if its cast or not.the thing that let go there looks pretty obvious to be the rods,especially since they don't seem to exist anymore haha,and maybe some tuning had to do with it but like already stated,those rods are only good for like 450hp at the very max limits.time for an upgrade on the bottom end if they plan to keep the boost going to it.
 

Gearbanger 101

Straight Outta Locash
20+ Year Stangneter
Aug 10, 2002
9,457
1,377
234
Ontario, Canada
Nov 19, 2008
#19
  • Nov 19, 2008
  • #19
clentonz said:
but that does look bad, I guess that's what you get for using a 6 bolt instead of a 8
Click to expand...

I would venture to say that the 6-bolt crank had nothing at all to do with it. My guess is that the high static compression ratio, coupled with stock hypereutectic pistons, powdered rods and a poor tune were what killed this engine.

Plenty of cast 6-bolt crank cars out there running more than the Cobra's stock 8psi of boost (mine included) that are surviving just fine. To be honest….I can’t say that I’ve ever seen a crank failure.

Going with the forged crank in the Automatic equipped cars was an unnecessary expense and a correct choice by Ford IMO. The cars shift lower and as such don't challenge the bottom end in the upper RPM ranges like the manual would. Mark VIII's and Continentals ran cast cranks for nearly 10-years without issue, so I really don't see the problem. And since the rest of the bottom end in these cars still suck, having a forged crank in place of the cast most likely wouldn't have made a lick of difference in the outcome.
 

EPIK

Member
Jul 3, 2004
796
1
16
LEFT COAST
Nov 19, 2008
#20
  • Nov 19, 2008
  • #20
If you guys would reread my OP, I never said the crank was the issue, I just mentioned that it had the "$h!tty 6 bolt cast crank"...


It was an automatic car with the $h!tty cast 6 bolt crank (unlike the manual cars with the 8 bolt Forged Cobra crank), but I doubt that had anything to do with the motors outcome....
Click to expand...
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
Took some pics, i do really own a mustang...
  • 2000xp8
  • Jun 20, 2023
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 6 7 8
Replies
148
Views
21K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 1, 2024
Mustang5L5
Progress Thread My budget '93 5.0 rebuild (pic heavy).
  • evintho
  • Dec 8, 2021
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
3K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 24, 2022
evintho
Fox 4 Cyl to V8 Swap Info Thread
  • Matt01
  • Jul 12, 2021
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
14K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 9, 2023
Robinson
R
A
1991 5.0 - fires up every time, idles perfectly, but once it’s warm it won’t idle for more than 15 seconds
  • AmericanMuscle4.6GT
  • Jul 27, 2021
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
48
Views
9K
Fox 5.0 Mustang Tech May 21, 2022
Mindseye007
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?