MSD Help Please

CooterXJ

New Member
Jan 30, 2006
20
0
0
Ft. Stewart, GA
OK let me start off with telling you the background info... I just got the car I bought it the way it is (he was leaving for the Airforce and I just got back from Iraq). We took it to the track Friday and we walked mid-high 13sec cars while not hooking up at all (bottle was empty, so no juice). Then Saturday night we were going to go out. Crusin down the road I accidently kicked the fue box. Then 5 minuts later at the traffic light I pushed in the clutch to put it in gear and the car just died. The car cranks but wont fire. Checked for spark and nothing. Had 12V going to the coil, so replaced the coil. New Blaster SS. Still she wont fire. But the battery is alittle low so there isnt quite 12Vs going to the coil (only 10V, but the car still cranks).

Now here is what is in the car. Carberated 302, MSD 6A, MSD Blaster SS coil (PN 8207), and MSD Billet distributor (PN 8582).

Please help me out... I want to have the car running by wendsday night so i can take her to the track, my drag radials will be in tomorrow.
 
Using the 1st link i tested the megnetic pick up... 539 ohms (its between the 400-1300). Damn and i just got back from buying a new one (not put on yet). American Motor Sports, tested my 6AL box to see if it was good while I was there.. and it is..... WTF

And yes I did check all the fuses.
 
Ground a spark plug and see if your getting spark, then check the dizzy, make sure all the wires to it are hooked up correctly, check the coil wires, trace them to where they go and make sure there are no nicks, cuts, none melted, etc.

Its cranking but not firing, so your either not getting fuel or spark. Take the coil wire off the dizzy and try to arc it over to the engine block or the frame of the car and see if it's producing spark, should be a nice blue spark, if it is, then the coil has spark and the dizzy is next in line to check. What type dizzy you running?
 
Yes I did check spark from the coil... No spark. MSD 6a is good had it tested at American Motorsports. Replaced the Blaster SS Coil. Tested the megnetic pick up in the distributor and its good too.

Its Carberated, its getting fuel. I cant bypass the 6A box, it is my ignition.
 
Its in the wiring, its more than likely not in the components, how many people ever seen an MSD box go out? Once in a few blue moons, Its more than likely in the wiring someplace. Trace everything back, follow all your wires, make sure none of them are messed up, came loose....If your not getting spark from the coil, than follow those wires that give power to the coil back to their source and check them. Get you a voltmeter.
 
CooterXJ said:
I do have a multi meter. The coil is getting power. But I have no spark out of the coil.

that is why i am so confused. I have one of the simplest and easyest systems to troubleshoot. F*in thing is drivign me nuts.

Take one of your plug wires and just temporarily use it for a coil wire and see what happens....Hell its worth a shot...
Double check a diagram and make sure you got your wires attached to the right sides of the coil, may seem basic, but its happend to me before. I replaced an entire fuel pump and relay and it turned out i left the positive wire off up in the engine bay. But what may have happend is that the old coil was bad, you installed the new one but got a wire crossed...you never know. Check your work against an MSD wiring diagram
 
Did you try to test the MSd Box yourself, There is instructions on how to do it. I have had them go bad in the past, If your dist. test properly , and obviously you have fuel, So my guess is the box isnt reading the signal from your dist. bypass the msd, or try another one.