• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

My 89 won't idle when cold

  • Thread starter Thread starter KENS89LX
  • Start date Start date May 25, 2006

KENS89LX

Member
Mar 12, 2006
302
1
19
Cross lanes Wv
May 25, 2006
#1
  • May 25, 2006
  • #1
After installing a March ram air system on my stang a few weeks ago the motor won't idle, so far I have installed a new rotor cap and button, cleaned the egr valve, adjusted the timing, and the tps but it did not help the idle when the engine is cold, it is fine when it warms up. It also bucks a low rpm's. :SNSign: What next?
 
S

Stangler

A.K.A. Mr. Hankey
Founding Member
Dec 20, 2001
1,357
1
37
May 25, 2006
#2
  • May 25, 2006
  • #2
Clean the mass air wire with brake clean.
 

KENS89LX

Member
Mar 12, 2006
302
1
19
Cross lanes Wv
May 25, 2006
#3
  • May 25, 2006
  • #3
I"ll try that, I just tried switching the IAC motor but it did'nt change anything. I have the c&l 76mm mass air meter and a 70 mm throttle body, would it make since the it is getting more air than fuel since the onle thing I did tto the fuel system is a 110 fuel pump. Would the stock mass air help?
 
S

Stangler

A.K.A. Mr. Hankey
Founding Member
Dec 20, 2001
1,357
1
37
May 25, 2006
#4
  • May 25, 2006
  • #4
Just pull out the electronics(two screws) clean the little wire that measures air flow, and put it back together. If that dosen't work, try roatating the meter. does that cold air kit have a 90deg elbo in front of the meter?

Nate
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 25, 2006
#5
  • May 25, 2006
  • #5
When using some aftermarket IAC's, check instructions to see if it needs to be mounted upside down. If it isnt, the car wont idle decently or at all while cold.

I would run codes. If needed, go through and reset your idle.

Good luck.
 

6SpeedLX

New Member
Apr 5, 2005
100
0
0
Mass
May 25, 2006
#6
  • May 25, 2006
  • #6
not to jack the thread or anything but im also having the same rough idle problem, it does it in the morning when cold and it bucks below 2200...i cleaned the MAF, put a new IAC in, new plugs, cap & rotor. i also have a C&L MAF and intake tube.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 25, 2006
#7
  • May 25, 2006
  • #7
See the sticky "Help me create the Surging Idle Checklist" at the top of the forum for help with your idle problems. The first most contains all the updates to the fixes. I continue to update it as more people post fixes or ask questions.
 

KENS89LX

Member
Mar 12, 2006
302
1
19
Cross lanes Wv
May 26, 2006
#8
  • May 26, 2006
  • #8
To answer your question Nate, I have the March Ram Air system. I am going to try cleaning the throttle body next. Plug wires after that!
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
May 26, 2006
#9
  • May 26, 2006
  • #9
Have you pulled the codes???????

Please do this first.
We (humans in general) can only take guesses. Even though they are educated guesses, the computer can give you more concrete information to work with.
(the above suggestions are all good)

Not all trouble codes will trigger the check engine light.

I'm not trying to be a jerk, and I apologize if I have come across that way.

I know how frustrating it can be to diagnose these things.

Good Luck,

jason
 
L

Lynx331

New Member
Jan 5, 2004
308
0
0
Chicago IL
May 26, 2006
#10
  • May 26, 2006
  • #10
I have the same problem with mine.... It will surge from about 500 to 2200 when i first fire it up. I pulled the codes and got nothin... basically i just got pretty good at how i touch the gas and when to touch it and i can usually get her to idle in a few seconds. Bascially a quick fix is just to play with the pedal some when shes cold.. atleast it works for me, after its warm she'll idle all day
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 27, 2006
#11
  • May 27, 2006
  • #11
As I said, see the sticky - some of Stangnet's best & brightest have contributed their experience to solving the idle problems common to 5.0 Mustangs.
 

DMAN302

My mom says thanks for the pearl necklace.
Nov 8, 2003
2,120
2
59
windsor, Canada
May 27, 2006
#12
  • May 27, 2006
  • #12
You indicate the issue started after the march kit install..I'm wondering if maybe you damaged or knocked off one of the vac lines around the area of the emissions equipment creating a vac leak. Next would be if the kit install created the issue..what happens when you go back to your previous set up
 

KENS89LX

Member
Mar 12, 2006
302
1
19
Cross lanes Wv
May 27, 2006
#13
  • May 27, 2006
  • #13
I don't have a code checker.. I just came in from cleaning the wires on the mass air, and the throttle body, and it was gummed up. If that don't work I am going to go to autozone to get the codes if there is any. Does anyone have the gt-40p heads on their stang? I am having trouble finding plug wires that fit without being very close to the headers, I just found two more that was burnt and cracked.. could have been my surging problem.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 27, 2006
#14
  • May 27, 2006
  • #14
Dump the codes and see what the computer says is wrong…

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/
OR
See http://www.mustangworks.com/articles/electronics/eec-iv_codes.html

IF your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.

Codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

For those who are intimidated by all the wires & connections, see http://www.actron.com/product_detail.php?pid=16153 for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Walmart.

Or for a nicer scanner see http://www.midwayautosupply.com/detailedproductdescription.asp?3829 – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $35.

By the way - this information is is the Surging Idle sticky...
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
May 27, 2006
#15
  • May 27, 2006
  • #15
my89blubyu said:
I don't have a code checker.. I just came in from cleaning the wires on the mass air, and the throttle body, and it was gummed up. If that don't work I am going to go to autozone to get the codes if there is any. Does anyone have the gt-40p heads on their stang? I am having trouble finding plug wires that fit without being very close to the headers, I just found two more that was burnt and cracked.. could have been my surging problem.
Click to expand...

When I switched to shorty headers I had to convert to plug wires with a 90* boot (as opposed to the stockers with a 45* boot).
The 90* boots I have are also much shorter than the stock units.
I have has no plug burning issues since.

Shorting out the plug wires can cause some major issues, but I would still look at the codes.

I check my codes at least every oil & filter change, sometimes more ofetn. Probably overkill, but it is so easy to do I figure why not.

I bought one of these scanners... http://www.autoxray.com/products.aspx?sub=readers&id=33
Some of them are affordable.

jason
 

KENS89LX

Member
Mar 12, 2006
302
1
19
Cross lanes Wv
May 27, 2006
#16
  • May 27, 2006
  • #16
checked codes with no problem, checked plugs and they were fouled badly, after installing new ones, the problem was SOLVED! I appreciate all the info... Thanks!
 

KENS89LX

Member
Mar 12, 2006
302
1
19
Cross lanes Wv
May 27, 2006
#17
  • May 27, 2006
  • #17
Checked the Haynes book on different plug situations by pic, says caused by either bad valve seals or bad gas. I'm thinking it is the gas, where I "used" to get it it had 10% additive in it, I think it was ethanol but not sure. Dose anyone run 89 octane that is what I am using.
 
You must log in or register to reply here.

Similar threads

7
Engine Random hanging idle
  • 706 Saleen
  • Feb 11, 2026
  • Fox 5.0 Mustang Tech
Replies
9
Views
866
Fox 5.0 Mustang Tech Feb 19, 2026
86HO5.0
8
8
Engine Rough idle and aggressive sputtering when accelerating
  • 88vertible
  • Aug 13, 2025
  • Fox 5.0 Mustang Tech
Replies
4
Views
1K
Fox 5.0 Mustang Tech Dec 13, 2025
Jarhead67
J
S
Fuel ‘88 GT Runs Rich Cold — Fixes Itself When I Unplug Sensors (ECT, MAF, O2, etc.)
  • Sufarry
  • Nov 6, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
1K
Fox 5.0 Mustang Tech Nov 9, 2025
Mustang5L5
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
627
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
S
Engine Stalls when downshifting/coasting
  • Scott_S
  • Nov 5, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
917
Fox 5.0 Mustang Tech Nov 6, 2025
Mustang5L5
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?