Need Felpro headgasket part #

red95gtconvert · Feb 16, 2008

Hello everyone I am installing my GT40P heads soon and need the Felpro part # for the headgaskets I will need to order, thanks in advance.

BlownFiveLiter · Feb 17, 2008

Fel Pro 1011-1 should get the job done.

red95gtconvert · Feb 17, 2008

Thanks.

Redsnk95 · Feb 17, 2008

I wouldn't get those. Get the 8548pt2 gaskets, same price better gasket.

blksn955.o · Feb 17, 2008

just for future ref. does anyone know the part number for the Fel-Pro new-ish multi layer steel gasket...the ones that have the rubber surround/coating? They look fairly hairy and am debating on swapping to them and studs when I pull my intake to put in new lifters.

I am running the 1011's now, but have had a hard time getting them to seal in the past FWIW. The last two have sealed fine but one set would not seal between a cyl. Since I have a 150 shot as my low

PUNISHER RACING · Feb 17, 2008

I always use 1011-2's

red95gtconvert · Feb 17, 2008

Thanks again everyone. I ended up going with the Felpro 1011-2's, I can't wait to get these heads installed, any horsepower guesstamations ?

BlownFiveLiter · Feb 17, 2008

blksn955.o said:
just for future ref. does anyone know the part number for the Fel-Pro new-ish multi layer steel gasket...the ones that have the rubber surround/coating? They look fairly hairy and am debating on swapping to them and studs when I pull my intake to put in new lifters.

Fel Pro 1133, IIRC.

PUNISHER RACING said:
I always use 1011-2's

Even with iron heads? They would still work, but given the choice, I'd prefer the steel ring of the 1011-1 versus copper on the 1011-2.

red95gtconvert · Feb 17, 2008

StangGT1995 said:
Fel Pro 1133, IIRC.

Even with iron heads? They would still work, but given the choice, I'd prefer the steel ring of the 1011-1 versus copper on the 1011-2.

Do you think it will make a difference?, I just went with what the tech at Jegs suggested which was 1011-2.

BlownFiveLiter · Feb 17, 2008

It shouldn't make a difference. The 1011-1 has steel fire rings, while the 1011-2 has copper. You need to use the 1011-2 with aluminum heads to limit the possibility of brinnelling from the stronger steel ring against the aluminum surface. With copper, it's a non-issue. You can use the 1011-2 with either steel or aluminum, although some electrolysis may occur between the dissimiliar metals (copper versus iron).

red95gtconvert · Feb 17, 2008

Cool, thanks again. I'll post pics and an update after I install the heads:SNSign:

blksn955.o · Feb 18, 2008

StangGT1995 said:
Fel Pro 1133, IIRC.

Great thanks

Need Felpro headgasket part #

red95gtconvert

New Member

BlownFiveLiter

have car, will race....wait, it doesn't run

red95gtconvert

New Member

Redsnk95

blksn955.o

PUNISHER RACING

Active Member

red95gtconvert

New Member

BlownFiveLiter

have car, will race....wait, it doesn't run

red95gtconvert

New Member

BlownFiveLiter

have car, will race....wait, it doesn't run

red95gtconvert

New Member

blksn955.o

Similar threads

Need Felpro headgasket part #

New Member

have car, will race....wait, it doesn't run

New Member

Active Member

New Member

have car, will race....wait, it doesn't run

New Member

have car, will race....wait, it doesn't run

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency