• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Need help from a Pro.

  • Thread starter Thread starter bdollarbill
  • Start date Start date Nov 27, 2005
Prev
  • 1
  • 2
  • 3
First Prev 3 of 3

bdollarbill

Member
Nov 27, 2005
89
0
6
Nov 29, 2005
#41
  • Nov 29, 2005
  • #41
Tmoss isn't thew orange wire on back of wiring harness the EEC ground wire? I thought it was anyway, I have a noid light kit I plan to use that later tonight to check wiring harness to each injector, the light should flash if workling properly correct?

Bill
 

bdollarbill

Member
Nov 27, 2005
89
0
6
Nov 29, 2005
#42
  • Nov 29, 2005
  • #42
Ok I got my noid light set in today, check the #1 & #5 injector harness both of those are flashing as they are working or should be working, I dont know if I should pull all the injectors & have them tested somewhere or what. Can you bench test an injector?

Bill
 

tmoss

Gettin Wired
Founding Member
Jun 28, 2001
7,153
32
128
Saint Louis, MO
Nov 29, 2005
#43
  • Nov 29, 2005
  • #43
The Orange wire is the 02 ground.........

I'd be suspecting the injectors after that test.......
 

Paul Perreca

New Member
Mar 30, 2005
1,085
0
0
Nov 29, 2005
#44
  • Nov 29, 2005
  • #44
my problem ended up being as stupid as FIRING ORDER -
5.0 HO is DIFFERENT FIRING ORDER than 5.0 non-HO

only diff is mine started, but didn't stay running, and ran like crap
 
P

PRO50SC

New Member
Dec 28, 2003
1,012
1
0
Olney, Maryland
Nov 29, 2005
#45
  • Nov 29, 2005
  • #45
Have you checked for fuel volume. You can have good pressure but not enough volume. Somethin' to look into. Maybe your regulator is bad and the fuel is just going back into the tank. You would have to block off the return line in order to find out.
Or if you have a relief valve on the pressure gauge you bought you could do it that way. Run a hose from the relief valve into a 12 or 16oz juice bottle. Open the valve and have someone crank the engine. The bottle should fill up in a matter of seconds.
 
8

89white50

Member
Nov 16, 2004
440
1
18
central MA
Nov 29, 2005
#46
  • Nov 29, 2005
  • #46
sure theres gas in the tank? and your gas gauge isnt broke? it sounds dumb but it might be something i would overlook.
 

bdollarbill

Member
Nov 27, 2005
89
0
6
Nov 30, 2005
#47
  • Nov 30, 2005
  • #47
Pro50sc
I did see a pretty good flow when I checked the fuel pressure I held the relief valve open to see if maybe line was locked with air or not suppling any volume & seems to be pumping good flow. I am goint to pull the upper intake off, check each individual injector to see any signs of them being fouled up, they are ford 36# units & look fairly new, but I didnt install them so maybe aome or all are bad.

Bill
 

bdollarbill

Member
Nov 27, 2005
89
0
6
Nov 30, 2005
#48
  • Nov 30, 2005
  • #48
Ok I am almost positive it has to be the injectors now I am removing them all has anyone ever heard of all the injectors being bad at same time? I heard of maybe 1 or 2 not firing but never all 8 bad at once.. ??

Bill
 
P

PRO50SC

New Member
Dec 28, 2003
1,012
1
0
Olney, Maryland
Nov 30, 2005
#49
  • Nov 30, 2005
  • #49
bdollarbill said:
Ok I am almost positive it has to be the injectors now I am removing them all has anyone ever heard of all the injectors being bad at same time? I heard of maybe 1 or 2 not firing but never all 8 bad at once.. ??

Bill
Click to expand...
Highly unlikely!!!
 

bdollarbill

Member
Nov 27, 2005
89
0
6
Dec 3, 2005
#50
  • Dec 3, 2005
  • #50
I am pulling top end of motor back down today, I was reading a few articles online on how if injectors are stored in open air they actually can rust & corrode inside causing the pintles to stick & there isnt really any repair to them if the pintles get damaged as they will leak pass the seal with pintle corroded even if cleaned. Also I'd like to know if anyone in forum has ever sent their injectors out for clean,reseal & flow testing? I don't have anyone local to do it but saw several hi-perf. shopd in Ca that offer a low $$$ service for such service assuming yours are good.


Bill
 

bdollarbill

Member
Nov 27, 2005
89
0
6
Dec 4, 2005
#51
  • Dec 4, 2005
  • #51
Ok for all those people following my saga on this no start no fuel problem, I have good news. "It's alive" i pulled the induction back off, pulled the fuel rail & injectors,valve covers off,double checked the timing making sure both valves were closed on TDC, all ok there, cleaned injectors with carb & choke cleaner,sprayed off immediately with shop air, ran a OHMS test all were 14.3- 14.4 for those whom may want to know for their own info,installed new upper intake gasket just to be safe, installed rest of induction. First test on restart was a same as before after adjusting dizzy a few degree's it let out a huge book thru exhaust. I said to myself allright I fianlly got fuel to motor. After 2 or 3 restarts & adjusting dizzy started & ran on its own. Man does it sound so good. That TF stage 2 cam has a giant lobe separation. I'm afraid it may be idling to low... But its at least running I am so glad to get this problem resolved. I wish I could say this or that was the problem but I am stumped I never found anything wrong with anything I disassembled. Maybe the injectors just needed a good bath & blowing shop air thru them helped?? Thanks to all those with advice & helpful hints to check out.



Bill
 
P

PRO50SC

New Member
Dec 28, 2003
1,012
1
0
Olney, Maryland
Dec 4, 2005
#52
  • Dec 4, 2005
  • #52
Awesome man!! Glad to hear you got her goin'!!!
 
Prev
  • 1
  • 2
  • 3
First Prev 3 of 3
You must log in or register to reply here.

Similar threads

1
Engine 91 mustang 302 Low acceleration car backfires pops and acts like it doesn’t want to take fuel
  • 1991Fox5.0
  • Oct 4, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Oct 6, 2025
1991Fox5.0
1
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
712
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
J
MEED HELP!! 86 mustang
  • Jacob0121
  • Jan 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
486
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 25, 2026
CAMTWO1070
Fox Help
  • 93fox85
  • Mar 22, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
327
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 23, 2026
Noobz347
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?