• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Need Help Please.....im going crazy!!

  • Thread starter Thread starter MY 85 GT
  • Start date Start date Jul 28, 2008
Prev
  • 1
  • 2
  • 3
  • 4
Next
First Prev 2 of 4 Next Last
R

Rick James

Member
May 13, 2007
172
3
19
burlington new jersey
Jul 28, 2008
#21
  • Jul 28, 2008
  • #21
Well,i personally think its ignition related,could only be wires,coil or distributor.You already ruled out the carb,if it was an internal mechanical prob with the engine it woud be a consistant problem weather it was cold or hot.Since its carbd theres alot less and cheaper parts that can go wrong.Figure...if its the original dist. and coil they are what 23 yrs old?WOW do i feel old.
 

MY 85 GT

10 Year Member
Mar 7, 2008
1,852
208
104
New Jersey
Jul 28, 2008
#22
  • Jul 28, 2008
  • #22
Rick James said:
Well,i personally think its ignition related,could only be wires,coil or distributor.You already ruled out the carb,if it was an internal mechanical prob with the engine it woud be a consistant problem weather it was cold or hot.Since its carbd theres alot less and cheaper parts that can go wrong.Figure...if its the original dist. and coil they are what 23 yrs old?WOW do i feel old.
Click to expand...


Well the coil is new too...its also an accel coil..new duraspark module..new carb..new plugs...timing is fine.Firing order is fine...the only thing im thinking is the Dizzy well the hall effect maybe...but why when hot not cold...and i thought when they went bad they went bad the car wouldnt run? Should i buy a rebuilt dist and try that? how hard are they to install? i did alot of small block chevy dizzys...never a ford i heard there hard to do because of the oil pump shaft or something?
 
R

Rick James

Member
May 13, 2007
172
3
19
burlington new jersey
Jul 28, 2008
#23
  • Jul 28, 2008
  • #23
I honestly have never had to change one yet on a ford,but i would assume as long as you are carefull pulling it out and made sure the oil pump shaft doesnt fall into the pan you would be o.k.Maybe get a chiltons/haynes book and take a look at it or maybe someone else thats done it can chime in.I really dont think its a major operation.
 

MY 85 GT

10 Year Member
Mar 7, 2008
1,852
208
104
New Jersey
Jul 29, 2008
#24
  • Jul 29, 2008
  • #24
Well i have no idea what to do now......I tried going to work this morining and usually the car runs fine until it get s hot...well forget that idea...i made it about 3 blocks..they car would idle but would not take gas...when i tried to get it to go it Backfired so bad thru the exhaust sounded like gun shots....the car stalled would start tried to move backfiring....finally got it back home which was 3 blocks away but barely..what can be going on with the CAR.....
 

1990Coupe

Founding Member
Mar 11, 2002
1,462
132
114
Toms River NJ
Jul 29, 2008
#25
  • Jul 29, 2008
  • #25
I'm putting my chips on the Wires or fuel pump. I don't care if its new, I had a fuel pump poo out on me a few hundred miles after install. Granted mine was an 86GT so i had fuel injection, but the car would revv no problem, once under load it wouldn't rev past 5 grand. As the days went by i couldn't get over 4 grand, then 3, then 2.. She would idle fine and rev under no load, once i put a load on her, she would stumble, backfire and die. I think its your pump mang
 

MY 85 GT

10 Year Member
Mar 7, 2008
1,852
208
104
New Jersey
Jul 29, 2008
#26
  • Jul 29, 2008
  • #26
1990Coupe said:
I'm putting my chips on the Wires or fuel pump. I don't care if its new, I had a fuel pump poo out on me a few hundred miles after install. Granted mine was an 86GT so i had fuel injection, but the car would revv no problem, once under load it wouldn't rev past 5 grand. As the days went by i couldn't get over 4 grand, then 3, then 2.. She would idle fine and rev under no load, once i put a load on her, she would stumble, backfire and die. I think its your pump mang
Click to expand...

I dont know about that i have a big old fuel pressure gauge staring me in the face....lol and the pressure never drops off when the car is acting up..it has 5.5-6 psi at all times....i would agree with you if the pump would go down to little or no fuel pressure but its not...I think its more electrically but what i dontknow...the plugs are new the wires arent that old cap and rotor arent that old replace the duraspark yesterday..only thing left is the Dizzt i guess....oh coil isnt that old either...
 

1990Coupe

Founding Member
Mar 11, 2002
1,462
132
114
Toms River NJ
Jul 29, 2008
#27
  • Jul 29, 2008
  • #27
WOW... completely forgot about that gauge
 
R

Rick James

Member
May 13, 2007
172
3
19
burlington new jersey
Jul 29, 2008
#28
  • Jul 29, 2008
  • #28
Any progress?
 

MY 85 GT

10 Year Member
Mar 7, 2008
1,852
208
104
New Jersey
Jul 29, 2008
#29
  • Jul 29, 2008
  • #29
Nope at work had to have a friend pick me up the car would even go today the idle was ok started right up tried to drive it forget it...Bucking ...misses....stalling and huge huge back firing thru the exhaust....scared the hell out of me...barely made it 3 blocks i had to turn around and barely made it back to my house....i have no idea whats wrong with it......any one have any idea....
 
R

Rick James

Member
May 13, 2007
172
3
19
burlington new jersey
Jul 29, 2008
#30
  • Jul 29, 2008
  • #30
I think a reman dizzy and wires from PEP BOYS or whoever, will probably cost about 100 bucks. JMO
 

MY 85 GT

10 Year Member
Mar 7, 2008
1,852
208
104
New Jersey
Jul 29, 2008
#31
  • Jul 29, 2008
  • #31
Rick James said:
I think a reman dizzy and wires from PEP BOYS or whoever, will probably cost about 100 bucks. JMO
Click to expand...


I know there not to exspensive but i dont want to attemp to do the dizzy myself i heard bad out comes on the oil pump shaft falling.If i can do it i would just dont feel like droping an oil pan....
 

RsStanG1987

I shaved all my pubes playing this game.
10 Year Member
Mar 13, 2004
569
9
79
Dupont PA
Jul 29, 2008
#32
  • Jul 29, 2008
  • #32
Im thinking timing issue without a doubt. you say it backfires through the exauhst? Mine did that when the timing was off.
 
R

Rick James

Member
May 13, 2007
172
3
19
burlington new jersey
Jul 29, 2008
#33
  • Jul 29, 2008
  • #33
Do some research on it,get a manual and give it a crack.Theres only one way to learn and its certainly not gonna fix itself.
 

MY 85 GT

10 Year Member
Mar 7, 2008
1,852
208
104
New Jersey
Jul 29, 2008
#34
  • Jul 29, 2008
  • #34
RsStanG1987 said:
Im thinking timing issue without a doubt. you say it backfires through the exauhst? Mine did that when the timing was off.
Click to expand...

Timing hasnt moved....i marked the Dist..way back when i got it...still ont hat mark...this problem started as a slight buck or stumble once in awhile not i cant even drive it so something got way worse...I thought it was the carb because it had a faulty casting for the step up springs...Replaced it woith a new carb that didnt help still runs the same....new dura spark module...stil runs the same ..new plugs...etc...Th eonly thing i think it could be is the Magnetic pick up in the dizzy but i thought they either work or dont work.,...Also i have no EGR valve spacer plate block off...I have a gasket....phenoilc spacer ...gasket..then carb...im wondering in that hole under the intake is effecting the air flow or air mixture...its stil the stock intake i have..i have no poluttion stuff anymore no air tubes no air pump eveything is gone....Im lost....the car ran ok after i took the EGR valve spacer plate off i took it off to put that phenolic spacer on due to the carb boiling over the EGR valve spacer plate was cast it held heat...so i took it off threw it away and that where on at now....
 

87coupe50

Member
Feb 10, 2008
105
1
16
WAYNESBORO, PA
Jul 29, 2008
#35
  • Jul 29, 2008
  • #35
Looking over the pics:

the black wire on the electric choke, is that a ground wire? maybe with the phenolic spacer it's not getting a good ground and causing something funky once the engine gets warm.

have you checked you cap and rotor? verify the timing! even though you have the dizzy marked, mke sure something didn't jump

the white electrical/vacuum connector, try putting some caps on the vacuum connectors
just tryin to help
 

MY 85 GT

10 Year Member
Mar 7, 2008
1,852
208
104
New Jersey
Jul 29, 2008
#36
  • Jul 29, 2008
  • #36
87coupe50 said:
Looking over the pics:

the black wire on the electric choke, is that a ground wire? maybe with the phenolic spacer it's not getting a good ground and causing something funky once the engine gets warm.

have you checked you cap and rotor? verify the timing! even though you have the dizzy marked, mke sure something didn't jump

the white electrical/vacuum connector, try putting some caps on the vacuum connectors
just tryin to help
Click to expand...


Yes the black wire is the ground...I think its ok i had the air cleaner off when i put the new carb on and i forgot to hook up the power wire when i did it opened and had tension on the choke flap so i think its ok....The cap and rotor well they look ok i replaced them a few months ago...im going to replace them again just to make sure there ok...I do nt htink i have any Vac leaks i set the carb up with a vac gauge yesterday it was steady and hels close to 20 inches of vac at idle..give it gas went to 0 then came back up to 20 again....I spoke to the Shop that did all my exhaust work all he works on is Mustangs he said sounds like the Magnetic pick-up is shot...could that be...If so he said pickup a new/rebuilt dizzy....i thought when a mag pick-up went bad in went bad wouldnt start the car or wouldnt run at all...
 
R

Rick James

Member
May 13, 2007
172
3
19
burlington new jersey
Jul 30, 2008
#37
  • Jul 30, 2008
  • #37
Any updates?
 

MY 85 GT

10 Year Member
Mar 7, 2008
1,852
208
104
New Jersey
Jul 30, 2008
#38
  • Jul 30, 2008
  • #38
Rick James said:
Any updates?
Click to expand...

Yeah he car runs like ****....lol...I found the fuel pump...pressure to be to hight bought a regulator checked the floats,threw it on adjusted seemed good...15-20minutes running like total ****...smae tign everyday...everynite...15-20 then it goes down the drain...Im going to try one more thing before i either run it into a wall...give up on iy and sell it....or bring it somewhere and hope they can find it....The last thing in doing is moving the coil of the intake and reloctaing it the fender....maybe just maybe its overheating after 15-20 mintues creating weak spark...So tomorrow when i come home im putting on a new cap and rotor new coil and coil wire and moving the coil way way away from any heat source...if it does it after that i give up!!!!!!!!!!!!!!!!!!!!!! And on top of it all i have a nice tick in the exhaust that i never had before im just hoping its a misfire from the igntion or something....

Anyone want to buy a cheap 85 GT
 
R

Rick James

Member
May 13, 2007
172
3
19
burlington new jersey
Jul 30, 2008
#39
  • Jul 30, 2008
  • #39
Dont give up,i would at least try a reman dizzy.If i wasnt working the next 10 days in a row i would even give you a hand but i cant right now.If you seriously are going to sell it tho ,p.m. me.But if you did sell it ,i can gaurantee youll regret it.
 

MY 85 GT

10 Year Member
Mar 7, 2008
1,852
208
104
New Jersey
Jul 30, 2008
#40
  • Jul 30, 2008
  • #40
Rick James said:
Dont give up,i would at least try a reman dizzy.If i wasnt working the next 10 days in a row i would even give you a hand but i cant right now.If you seriously are going to sell it tho ,p.m. me.But if you did sell it ,i can gaurantee youll regret it.
Click to expand...


Thanks for the other... Im sure it will still be not running right in 10 days....LOL....Im going to try the re-locating the coil and new cap and rotor...see what happens last thing is a Dizzy which i ordered so at least i'll have it but im not putting it in myself...lol..i'll take it somwhere.....And i am serious if tis car doesnt run good soon its gone...I cant have this type of headache i need it to get back and forth to work..i already lost 3 days in the last 2 weeks because of it not running right....
 
Prev
  • 1
  • 2
  • 3
  • 4
Next
First Prev 2 of 4 Next Last
You must log in or register to reply here.

Similar threads

P
Fuel New Eldebrock 1406 problems 1985 GT 5.0
  • Paddyman
  • Oct 22, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
173
Fox 5.0 Mustang Tech Nov 2, 2026
manicmechanic007
M
Need help please
  • Mikey62666
  • Oct 12, 2026
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
1
Views
130
2005 - 2014 S-197 Mustang -General/Talk- Oct 14, 2026
gkomo
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
517
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
C
Electrical Fuel Gauge...Help! What did I do or Didn't Do?
  • ChickenDeluxe
  • Sep 3, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
246
Fox 5.0 Mustang Tech Sep 3, 2026
ChickenDeluxe
C
F
86 notch NEED HELP!!!!
  • foxbody86
  • Jul 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
165
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 9, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?