• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Need help with tranny hardware..

  • Thread starter Thread starter jmir018
  • Start date Start date Aug 31, 2005
J

jmir018

Founding Member
Jul 27, 2002
94
0
0
foster city, san mateo, san francisco, CA
Aug 31, 2005
#1
  • Aug 31, 2005
  • #1
OK, so I just had a crap load of work done to a 91 coupe. I crawled underneath the car today to see where all the oil or power steering liquid seemed to be coming from (different story) and noticed something weird on the bellhousing.

First of all, at the bottom of the bellhousing and flex plate there seem to be two holes, one on each side, where you could place a bolt to secure it in place. But I have nothing there. I don't remember if I ever did or not.

Second problem, there is a hole in my bellhousing you can see the clutch cable going into it.. and you can see the clutch in there. should there be a plate covering it? i remember seeing one in my tranny before i had all this work done. should there be one or am i mistaken? it seems unsafe to have that whole there because water, rocks or whatever could go in there and damage the clutch up.

pd: i also hear somewhat of a ticking noise coming from the power steering pump. what could be causing this? thanks.
 

88gt

Founding Member
Aug 2, 1999
794
0
0
Drillers cabin
Aug 31, 2005
#2
  • Aug 31, 2005
  • #2
On the first one; I believe there should be a couple of bolts/screws there. I think you are talking about the thin metal cover on the bellhousing.

On the second; yes there should be a cover there. As far as junk getting in there and messing the clutch up, the risk is very low. I personally prefer that it be there. If you have it and the little screw that holds it in place, it only takes a few minutes to put back in place.

Sorry I could answer better on the first one.

Jim
 
N

NUTCASE

New Member
Mar 31, 2005
187
0
0
Aug 31, 2005
#3
  • Aug 31, 2005
  • #3
you should be able to go to a junk yard and get the cover/bolt and the 2 or 3 1/2 inch bolts that go to that sheetmetal cover
 
J

jmir018

Founding Member
Jul 27, 2002
94
0
0
foster city, san mateo, san francisco, CA
Aug 31, 2005
#4
  • Aug 31, 2005
  • #4
the junkyards by my house don't have trannies on them. they remove them before they brign the cars in.
 
You must log in or register to reply here.

Similar threads

M
1996 GT Speedometer electrical nightmare
  • moon96gt
  • Oct 7, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
177
SN95 4.6L Mustang Tech Oct 17, 2026
CAMTWO1070
S
Car shakes when taking off help???
  • STANKYstangs
  • May 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
12
Views
548
1996 - 2004 SN95 Mustang -General/Talk- May 27, 2026
LILCBRA
S
Engine Stalls when downshifting/coasting
  • Scott_S
  • Nov 5, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
899
Fox 5.0 Mustang Tech Nov 6, 2025
Mustang5L5
K
TKX Transmission Shifting Problem
  • KWC156
  • Jun 23, 2025
  • Other Auto Tech
  • 2
Replies
21
Views
3K
Other Auto Tech Jun 13, 2026
427nostang
4
Garage Lighting
  • gkomo
  • Oct 20, 2025
  • Off-Topic Hangout
Replies
14
Views
275
Off-Topic Hangout Nov 29, 2025
Clutchfork
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?