• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

New 306 OVERHEATING?

  • Thread starter Thread starter 91coupestang
  • Start date Start date Sep 26, 2007
9

91coupestang

New Member
Apr 14, 2007
1
0
0
Walnut Cove, NC
Sep 26, 2007
#1
  • Sep 26, 2007
  • #1
I just had a 306 built for my 91 coupe. I used the 10.3:1 forged kit from Summit. I used AFR 165s w/ 58cc, Cometic mls gaskets, trick flow street cam/intake, long tube BBk headers, 30lb matched injectors, 76mm C&L pipe, 70mm BBk throttle body.
I had to remove the drivers side head due to the gasket being put on backwards, covering up the water jackets at the rear of the block. I installed a new stock replacement water pump, w/ a new 2 row alum radiator. 160 deg thermostat.

I filled the system from the heater hose w/ a water hose to get all the air out of the system. I let the car come to operating temp, then installed the radiator cap and drove for about 48 miles. I also let the car sit and run for over 20 minutes midway through the drive. I have an aftermarket h2o sensor on the drivers side rear intake, it was reading around 180/190 degrees, the factory front one was 150/160 degrees. Good so far.

I drove it the next morning and the temp went to 230 degrees w/i 2 mile from the house. I came home and the temp had risen to 250. I let it cool, filled it up again (it had boiled out some when it got hot) w/ the heater hose and it did fine. Again the next day, it overheated w/i 2 miles from the house.

It seems to be getting air in the system from somewhere. Any ideas or help?
 

87foxstang

Member
May 10, 2007
0
0
16
Cromwell, CT
Sep 26, 2007
#2
  • Sep 26, 2007
  • #2
ive always heard that the 306's run hot, but damn. Sorry i cant really think what the problem could be, but i know others will.
 

fivespeedsteed

20+ Year Stangneter
Oct 17, 2003
748
22
69
Richmond, VA
Sep 26, 2007
#3
  • Sep 26, 2007
  • #3
how do 306's run more hot than 302's?
 
F

Fox8950

Member
Jun 29, 2007
247
2
18
Sep 26, 2007
#4
  • Sep 26, 2007
  • #4
I had the exact same problem after I rebuilt my 302 and had a completely dry system .. Lots of air bubbles can hide in there I know it took a good 3 or 4 times for me topping off/driving for a while. I know alot of people jack the front end up as high as they can on an initial fill and let it run that way, can't say as to how this works but wish I woulda tried it first As long as your not puffin smoke and/or smelling sweet stuff I'd say your ok and just still working the bubbles out.
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Sep 26, 2007
#5
  • Sep 26, 2007
  • #5
ALOT OF TIMES WHEN A ENGINE GETS OVER 240* OR SO THE STAT CAN COLLAPSE OR FAIL . I WOULD SUGGEST REPLACING THE STAT WITH A NEW ONE AND REFILLING THE SYSTEM WITH THE CAP OFF TILL THE AIR IS ALL PURGED. YOU CAN ALSO GET A BLEEDER TO SCREW INTO YOUR MANIFOLD WATER JACKET BUNGS.
 

408gt91

Member
Apr 29, 2007
114
0
16
N.H.
Sep 27, 2007
#6
  • Sep 27, 2007
  • #6
this stopped my old 306 from overheating.
 

Attachments

  • fan.webp
    2.3 KB · Views: 165

ninety15.0

New Member
Mar 10, 2004
1,336
0
0
Sep 27, 2007
#7
  • Sep 27, 2007
  • #7
You probably still have some air in there...try burping the system by pumping the upper rad hose while you are filling it up. After you think there is no air in the system, complete a pressure check to make sure the cooling system is holding pressure. Is the cap new? Also i dont know why you are running a 160° Tstat. That is too cold for our motors...you would be better off with a 180° setup. Good luck man
 

Flavadave4

Active Member
Nov 28, 2003
1,044
21
49
Utica, NY
Sep 27, 2007
#8
  • Sep 27, 2007
  • #8
Just get the air bubbles out and you'll be fine, there is no reason a 306 would run hotter than a 302......if everything is tuned and runnning correctly.
 

load71

New Member
Oct 28, 2004
68
0
0
Sep 27, 2007
#9
  • Sep 27, 2007
  • #9
I would go autozone to rent a radiator pressure check. Or if you have one, to see if you system is holding pressure. And I agree that 160 is way to low. They were 195 stock, and the computer likes the engine to be warm. And hopefully u didnt warp the those heads cause of how high ur temp got
 

mustangmike6996

5 Year Member
Nov 10, 2005
483
6
29
clinton twp, MI
Sep 27, 2007
#10
  • Sep 27, 2007
  • #10
head gasket on backwards????


jack the car up on the side with the radiator cap and let it run to get bubbles out...
 
You must log in or register to reply here.

Similar threads

Engine 1986 GT Overheating issues
  • 86 5O GT
  • Jan 25, 2026
  • Fox 5.0 Mustang Tech
Replies
18
Views
964
Fox 5.0 Mustang Tech Jan 29, 2026
86 5O GT
Engine Themostat
  • Mindseye007
  • Jan 30, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
1K
Fox 5.0 Mustang Tech Feb 1, 2026
86HO5.0
8
J
Engine Stalling
  • josh40tay
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
201
Fox 5.0 Mustang Tech Oct 21, 2026
JD1964
Engine Coolant boiling in hose?
  • Teen'93stang5.0
  • Jun 3, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
352
Fox 5.0 Mustang Tech Jun 8, 2026
Mustang5L5
M
Resolved 1988 Foxbody - Overheating Summer
  • MDrisc
  • Oct 26, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Jul 17, 2026
fasterthangas
F
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?