new short block on the way

94gt5.o · Feb 20, 2011

lol oh I will I'm still waiting to get my block then once my work bonus comes i get my heads I'm leaning towards the e streets cuz those trickflow heads that FIVEOHWBLOW posted are 950 per head lol not for both. almost had me.

94gt5.o · Feb 20, 2011

so i was looking at cams earlier and I looked at both the trickflow stage 1 and stage 2 the stage 1 is a lil on the small side stage 2 is to big.
I started looking at comp cams and they have a huge veriety of cams my question is is anybody running a comp cam with sumthing along the lines of my build thanks again for all the help guys. And once i get the block and heads there will be plenty of pics lol

revhead347 · Feb 20, 2011

Call Comp cams directly. They have a huge selection, and if you get someone good on the phone, they will be able to figure something out.

Kurt

94gt5.o · Feb 20, 2011

ok thanks

94gt5.o · Feb 21, 2011

The block showed up to day and let me tell you I could not be happier. If anybody is thinking of going this route do it. Cant wait to get more parts, The only thing is that im missing the male peaice the allows the oil filter to be screwed on any one know what its called? Oh and where to get a high volume oil pump, and one more question any body have an opinion on the block color

BlackVert · Feb 21, 2011

just sayin

94gt5.o · Feb 22, 2011

lol I know I know there will be pics tommarow when i get it on the engine stand. Trust I would have tonight but the gf has the compter skills and the camera lol

revhead347 · Feb 22, 2011

For the male piece for the oil filter, call Competition Products, they might have it. Another thing to check for is dowels. There should be 2 dowels for the transmission, 4 dowels for the cylinder heads, and two dowels for the timing cover. You usually have to buy these as part of a "Finishing Kit."

Competition Products

You can get a Melling High Volume Oil pump. It's a part number M-68HV. I usually get them at Advance Auto locally, because then if I have to warranty it out, it's a lot quicker than shipping it back to Summit. Price is about the same, around $40.

Kurt

RIO5.0 · Feb 22, 2011

High volume pump on a stock pan...read somewhere this "could" tend to suck the pan dry prematurely under the right conditions??

94gt5.o · Feb 23, 2011

no good I think new stock parts should be good enough right? Any opinons on block color?

BlackVert · Feb 23, 2011

my understanding is that the only time a high volume oil pump is needed is when you are planning on adding on something that has an oil feed, like a blower for example. then you would also be advised to get a larger pan because you definately don't want to pump the pan dry.

if you aren't planning on boosting it, then a standard volume pump is fine.

94gt5.o · Feb 23, 2011

ok well ive just ordered all my oiling system needs pump,pick up tube,oil pan, oil presure sending unit,ARP oil pump shaft, and oil pan gasket. So that pretty much takes care of the bottom end so it can be all put togather and get this motor rollin. So i think i found my cam I havent called comp cams yet but i just happend to stumble on it here are the specs.
1985-95 Mustang 5.0/5.8L Comp Xtreme Energy Camshaft, Hydraulic Roller, Fw Xe270hr-12 by Comp Cams

This cam is intended for Mass Air Equipped 86-95 Mustangs with Good Flowing Cylinder Heads, Intake Manifold, and Headers. Perfect for a "bolt-on" Modified Mustang. Your Mustang needs a minimum of a 3.23-3.73 rear-end.

Comp Cams Xtreme Energy XE270HR

For use with 1.7 Roller Rockers

Hydraulic Roller camshaft for use with 1.7:1 rockers. Mild modifications, 3.20 - 3.73 gears, larger throttle body and mass air, good heads and manifold.

270/276 advertised duration

218/224 duration @ .050"

.544/.544 lift (with 1.7 rockers)

112° lobe seperation angle

1800-5800 RPM operating range

what do you guys think?

RIO5.0 · Feb 23, 2011

94gt5.o said:
no good I think new stock parts should be good enough right? Any opinons on block color?

The block color gets kinda muted out on our motors to me...we have so much peripheral crap you really dont see much...I choose Black as it's easy to touch up. Depends on your choice of intake/VC color and such... I went with mostly Aluminum colors on my parts. Alot of the block is gone once you add your front brackets/accessories. Bout the only area that shows is under your heads...unless your gonna do a wire hiding job and maybe have no AC ???

For example here's mine all built...you see jack once the AC bracket goes on...

revhead347 · Feb 23, 2011

Way too much cam for iron heads.

Kurt

BlackVert · Feb 23, 2011

so long as you realize (and are ok with it) that it won't be optimal until you upgrade the heads, i can understand your thought process here. it's definately easier to replace the heads with the engine in the car than it is to replace the cam. i think it makes sense to install the final cam now before the engine goes in the car.

... so long as you realize (and are ok with it) that it won't be optimal until you upgrade the heads ...

94gt5.o · Feb 23, 2011

lol im doing aluminum heads im doin Edelbrock E-Street Cylinder Heads thought i mentioned this on an above thread here are the specs.

Application. The Edelbrock E-Street Aluminum Cylinder Heads are designed to be a direct bolt-on for 1986 to 1995 5.0L Ford V8 engines.

Specifications:

* Combustion chamber volume - 60cc
* Intake runner volume - 170cc
* Exhaust runner volume - 60cc
* Intake valve diameter - 1.90"
* Exhaust valve diameter - 1.60"
* Valve stem diameter - N/A
* Valve guides - Manganese bronze
* Deck thickness - 5/8"
* Valve spring diameter - 1.25"
* Valve spring maximum lift - 0.550"
* Rocker stud - 3/8" with guide plate
* Guideplate - Hardended steel
* Pushrod diameter - 5/16"
* Valve angle - N/A
* Exhaust port location - Stock
* Spark plug fitment - 14mm x 3/4 reach, gasket seat

Technical Notes. Use with hydraulic camshafts .550" max lift. Recommended spark plugs 14mm x 3/4" reach with flat gasket seat. Requires hardened pushrods. 289-302 cid with 7/16" head bolts requires #9680 head bolt bushing kit. 1.90" heads are ideal for stock pistons; 2.02" heads require additional piston to valve clearance.

By the way RIO5.0 that motor is breath taking lol

revhead347 · Feb 24, 2011

My apoligies, that cam is about right. I'm posting on several of these new motor threads on several forums, and I got confused.

Kurt

BlackVert · Feb 24, 2011

94gt5.o said:
lol I know I know there will be pics tommarow when i get it on the engine stand. Trust I would have tonight but the gf has the compter skills and the camera lol

um, tomorrow has come and gone bro.

94gt5.o · Feb 24, 2011

I took pics last night and hey will be up today girlfriends B day comes first lol
Revhead347 its ok lol. The cam seems pretty healthy but im wondering how the computer will like it? But it will be tuned no matter what on a dyno.

RIO5.0 · Feb 24, 2011

My FTI cam has more lift and the same LSA at 112...mine runs fine. I do get low speed bucking in 1st or 2nd, but had that with my Steeda 19 cam...I still run a the stock puter and its fine...Not saying a chip wouldn't help.

Your doing a chip so I won't go into other things you would get....

new short block on the way

94gt5.o

New Member

94gt5.o

New Member

revhead347

Apparently my ex-husband made that mistake.

94gt5.o

New Member

94gt5.o

New Member

BlackVert

94gt5.o

New Member

revhead347

Apparently my ex-husband made that mistake.

RIO5.0

94gt5.o

New Member

BlackVert

94gt5.o

New Member

RIO5.0

revhead347

Apparently my ex-husband made that mistake.

BlackVert

94gt5.o

New Member

revhead347

Apparently my ex-husband made that mistake.

BlackVert

94gt5.o

New Member

RIO5.0

Similar threads

new short block on the way

New Member

New Member

Apparently my ex-husband made that mistake.

New Member

New Member

New Member

Apparently my ex-husband made that mistake.

New Member

New Member

Apparently my ex-husband made that mistake.

New Member

Apparently my ex-husband made that mistake.

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency