• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Noisy T5...Going Bad?

  • Thread starter Thread starter onefstsnake
  • Start date Start date May 11, 2006

onefstsnake

New Member
Nov 25, 2005
792
1
0
Northern VA
May 11, 2006
#1
  • May 11, 2006
  • #1
Well I broke an axle a week ago and just got the car back.

I replaced both axles and the differential.
31 Spline Moser Axles and an Auburn Pro Locker w/ 3.73's

Well Maybe its just bacause I havent driven the car in a week, but the tranny seems alot noisier...
When I get off the gas and leave it in gear it sounds like rocks tumbling around...

Seems a little notchier too when I shift. Im wondering if I hurt the tranny when the axle broke...

Also, do T5's break often when launching hard? Or do they normally break from shifting hard?

This car is my DD so I dont wanna break much...

Thanks.
Ken
 
J

jaybquick

New Member
Dec 4, 2004
27
0
0
May 11, 2006
#2
  • May 11, 2006
  • #2
I have broken mine both ways. I have sheared the teeth clean off 3rd and 1st. So yes on launch and yes on a 2 to 3 power shift. Of course I have a lot of power. But I have rebuilt many a T5 and they are known to break with abuse. Unless they fooked up when they did the rear end. Can you tell for sure that the noise is coming from the trans?
 

onefstsnake

New Member
Nov 25, 2005
792
1
0
Northern VA
May 11, 2006
#3
  • May 11, 2006
  • #3
yeah I can feel it in the shifter.

I can usually feel a little vibration in the shifter, but it seems to be more than normal now. Unless Ive just forgotten how it feels...

But I know its noisier.

Also, If Im in the higher RPM range of 1st or 2nd gear and then put the clutch in I get alot of noise untill I put it in neutral and release the clutch. Not sure if this is normal or not...

BTW Im putting down 220rwhp and 285rwtq and running MT DR's
 

dragnazz5.0

My "0" key d0esn't w0rk, s0 I have t0 use the zer0
Nov 19, 2005
815
5
18
mooresville, nc
May 11, 2006
#4
  • May 11, 2006
  • #4
check the fluid level in it first. low fluid will cause a noisy shifter. other than that, youll just have to pull the cover off and check out whats going on.
 
S

Sicarius428

Active Member
Jan 6, 2004
2,085
5
49
May 11, 2006
#5
  • May 11, 2006
  • #5
I had a similar sound out of my freshly rebuilt transmission. Turns out that the roller bears that goes inbetween the input and output shaft were extremely soft and flat spotted. It ate up both of my shafts. Try the fluid first but it could be a bad bearing. The kit I used was from Hanlon. Hopefully it was just me that got a bad set of bearings(the caged bearing on the input was a bit soft too).
Kevin
 

onefstsnake

New Member
Nov 25, 2005
792
1
0
Northern VA
May 11, 2006
#6
  • May 11, 2006
  • #6
Fluid is fine, I dumped a bunch in when I put my TriAx on...
 
S

Sicarius428

Active Member
Jan 6, 2004
2,085
5
49
May 11, 2006
#7
  • May 11, 2006
  • #7
Unfortunately you probably won't know unless you drop the tranny. You sure its not the rear end or possibly the clutch/throw out bearing maybe?
Kevin
 

onefstsnake

New Member
Nov 25, 2005
792
1
0
Northern VA
May 11, 2006
#8
  • May 11, 2006
  • #8
Can I replace the TOB without drapping the trans?

B/C Im pretty sure mine is shot.
 
J

jaybquick

New Member
Dec 4, 2004
27
0
0
May 11, 2006
#9
  • May 11, 2006
  • #9
onefstsnake said:
Can I replace the TOB without drapping the trans?

B/C Im pretty sure mine is shot.
Click to expand...

Nope
 

SteedaGT9150

Advanced Member
Nov 10, 2004
1,351
59
68
Maryland
May 11, 2006
#10
  • May 11, 2006
  • #10
my TOB is shot too and it sucks driving around hearing that damn noise
 

Booksix

New Member
Dec 8, 2003
179
0
0
San Diego, CA
May 14, 2007
#11
  • May 14, 2007
  • #11
Kinda an old post but none the less:

I just developed this same sound (I described as "rocks tumbling around") in my drivetrain (T5 with about 25k, 7 year old king cobra clutch - still grabs great, adjusted properly). It's been getting worse.

Also, when I roll up to a stop sign, if I put the clutch in, it sounds like the clutch disc is spinning for a few seconds, slowly spinning down and then stops - with the car still moving. I had 2 helpers for just a couple hours and we managed to get a new throw out bearing in but that was all we had time before we had to get the car back together... So it's not that. But it's definitely something around the clutch. Seems to be related to engine speed, not car speed. And it seems to intensify if I get on the brakes without putting the clutch in...

Did you resolve your problem, onefstsnake? What was it?
 

onefstsnake

New Member
Nov 25, 2005
792
1
0
Northern VA
May 15, 2007
#12
  • May 15, 2007
  • #12
nope, still noisy.

Im just going to save up some money and get the Astro gear set put in along with a new clutch and flywheel.
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
May 15, 2007
#13
  • May 15, 2007
  • #13
onefstsnake said:
Can I replace the TOB without drapping the trans?

B/C Im pretty sure mine is shot.
Click to expand...

after that comment, i recommend you dont even change the oil dude
 

Booksix

New Member
Dec 8, 2003
179
0
0
San Diego, CA
May 15, 2007
#14
  • May 15, 2007
  • #14
ahh, come on! I thought the same thing at first but then remembered that I knew nothing about cars (except how to change an 81 buick oil filter) when I tore into my perfect 88 TC to swap the turbo 4 for a HO 8...
 

onefstsnake

New Member
Nov 25, 2005
792
1
0
Northern VA
May 16, 2007
#15
  • May 16, 2007
  • #15
Fluid was changed and refilled. No difference in noise.

Ill pick up the Astro gear and shaft set and a new clutch, TOB, pilot bushing and rear main seal.

Should be a weekends worth of work...

The car isnt going anywhere soon so Ill probably just drop the trans tomorrow and start taking it apart.
 
You must log in or register to reply here.

Similar threads

3
Eight inches is enough for me...
  • 351MooseStang
  • Nov 27, 2025
  • 1974 - 1978 Mustang II Talk & Tech
Replies
5
Views
801
1974 - 1978 Mustang II Talk & Tech Mar 2, 2026
Bullitt347
Drive Shaft/Rear Diff Issue on 2014 GT
  • DudeStang
  • Jun 16, 2025
  • 2010 - 2014 Specific Tech
Replies
11
Views
2K
2010 - 2014 Specific Tech Jan 21, 2026
gkomo
B
Questions About T5 Manual
  • Blackout67
  • Apr 13, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
10
Views
806
1996 - 2004 SN95 Mustang -General/Talk- Apr 22, 2025
89ripper
New Member with a 1992
  • Clutchfork
  • Oct 18, 2025
  • The Welcome Wagon
Replies
5
Views
446
The Welcome Wagon Oct 19, 2025
Clutchfork
Place to Avoid: Jamison Auto Group in Gulfport, MS
  • D Durden
  • Oct 20, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
46
Views
4K
1965 - 1973 Classic Mustangs -General/Talk- Jul 16, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?