• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Not 5.0 question, but tech.

  • Thread starter Thread starter dstanggt50
  • Start date Start date Dec 17, 2005

dstanggt50

Founding Member
Sep 13, 2000
1,316
0
0
Woodinville, WA
Dec 17, 2005
#1
  • Dec 17, 2005
  • #1
I'm doing an alternator for a 96 honda passport, 3.2 v-6, I thought this was going to be simple, only one plug and one power wire, so I replaced and have to jump the car because of the drained battery and my jumper cables started to smoke, like catching on fire or something. I don't have the cables crossed, new battery and terminals are clean. Could the actual alternator be causing this problem I dont' have anything crossed, just one power wire and one plug.
 

BLOWN 5.0 FOX

Member
Apr 4, 2005
213
0
16
NORTH SHORE MA
Dec 17, 2005
#2
  • Dec 17, 2005
  • #2
Sounds to me like your alt isnt charging check voltage at the stud on the alt should be around 15v good luck
 

dstanggt50

Founding Member
Sep 13, 2000
1,316
0
0
Woodinville, WA
Dec 17, 2005
#3
  • Dec 17, 2005
  • #3
So if the alternator isn't charging, it will cause the cables to jumper cables to burn?? , I thought maybe something to do w/the regulator or something overcharging??. It didn't do this before I replaced the alternator, and I double chk my install, looks good, like I said, only a couple of wires, it would be pretty hard to mess this up.
 
T

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
Dec 17, 2005
#4
  • Dec 17, 2005
  • #4
I don't see how the alternator would cause the cables to smoke. Make sure you have them connected correctly; hook up on the jumper (good battery) car normally and attach the red to the positive battery terminal on the honda - the black should go to a good ground - not the negative battery terminal (it could, but this is just in case your battery ground is bad).
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Dec 17, 2005
#5
  • Dec 17, 2005
  • #5
If not mentioned, double check that all cables are tight. Heat and smoke can come from loose connections (resistance).

Good luck.
 
S

SmockDoiley

New Member
Jun 14, 2003
1,591
2
0
San Diego, CA
Dec 17, 2005
#6
  • Dec 17, 2005
  • #6
You could possibly have a problem with the starter. If there is a short in the starter or in its wiring it could have drained the battery and is now frying those jumper cables.
 
You must log in or register to reply here.

Similar threads

3
Electrical Starter solenoid out of space?
  • 387lx
  • Jan 22, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
520
Fox 5.0 Mustang Tech Jan 23, 2026
387lx
3
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
405
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
D
Electrical Need some Altenator wiring help please.
  • DanB93
  • Feb 3, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
655
Fox 5.0 Mustang Tech Apr 7, 2025
Rcdgl
R
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
485
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
J
Power Wire Upgrade Question
  • jhaling
  • Dec 21, 2025
  • SN95 4.6L Mustang Tech
Replies
2
Views
358
SN95 4.6L Mustang Tech Mar 23, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?