• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Oil Dipstick question

  • Thread starter Thread starter kpack5982
  • Start date Start date Nov 7, 2006

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Nov 7, 2006
#1
  • Nov 7, 2006
  • #1
I just got done putting headers on my car and instead of taking off the oil dipstick like I should have I just bent it out of the way, like a moron. So I pulled the dipstick out to check the oil after I was done and low and behold it wouldn't go all the way back in. So now the tube the dipstick goes in is bent to hell by the oil pan. How do I remove the tube? Does it unscrew or what, the chilton doesn't say. Also, would I have to drain the oil to replace the dipstick tube? AHHH, this thing is frustrating!!!
 

Blk91stang

Member
Jan 3, 2003
607
0
16
North Brunswick, NJ
Nov 7, 2006
#2
  • Nov 7, 2006
  • #2
just pull it out. when you put a new one in, put some rtv on the outside of the tube and slide it in and bolt it to the header bolt.
 

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Nov 7, 2006
#3
  • Nov 7, 2006
  • #3
so it'll just slide right out? no oil spill or anything?
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Nov 7, 2006
#4
  • Nov 7, 2006
  • #4
yes, just as Blk91stang stated it should just pull out with enough force. dont worry about spilling oil it does not reach this level...if you have trouble pulling tube out you can use a flat screw driver at the base of the block where tube enters and pry under the bevel in the tube between bevel and block this will loosen the tube. as Blk91stang
stated coat the new oil tube under the bevel with rtv and insert into hole after it inserted into the hole i also used an adjustable wrench and adjusted it to the size of the tube above the bevel, and tapped the adj. wrench driving tube into the tube hole to get a good seat ensuring tube wont blow out.....
 
B

bentley429

Banned
Nov 25, 2004
528
3
0
Connecticut
Nov 7, 2006
#5
  • Nov 7, 2006
  • #5
Do exactly what those guys said and you'll be all set. If you cant bend it back good luck finding one, ebay is prob your best bet.
 

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Nov 9, 2006
#6
  • Nov 9, 2006
  • #6
I'm just gonna plug the hole, well at least for now, I plan on a bigger oil pan here soon anyways. Is the part number for the hole Clevite 219-2185? Anybody have experience pluggin the hole with this plug from napa?
 
D

Deleted member 87397

Nov 9, 2006
#7
  • Nov 9, 2006
  • #7
It's not a threaded hole so it might be kind of hard to plug.
 

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Nov 9, 2006
#8
  • Nov 9, 2006
  • #8
Yeah, I just saw that somewhere and was curious if you had to thread the hole first or what? I wondered what it looked like, i read that it was an "expansion plug"
 

white_97_GT

Member
Jun 19, 2004
76
0
9
Ontario, Canada
Apr 18, 2007
#9
  • Apr 18, 2007
  • #9
just buy a new one, $20 for a nice chrome one
 

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Apr 18, 2007
#10
  • Apr 18, 2007
  • #10
actually that is what I did do. I used the expansion plug thing and it worked great for a while, but I needed to check my oil and got one of the nice adjusting or whatever they are called. Can't remember the brand name but starts with an L and is a hellalot nicer than the stock one.
 

Roland69

Sergeant Tangnet
Sep 17, 2005
2,867
3
58
Port Elgin, Ontario
Apr 18, 2007
#11
  • Apr 18, 2007
  • #11
Ford could order you a stock replacement...For now tou could just cut it about half way down and pinch the end shot to stop oil from comming out....and they just pull out there is an O-ring that holds them in place.
 
You must log in or register to reply here.

Similar threads

W
Dipstick
  • wccurtis1963
  • Jun 13, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
274
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 20, 2026
Willybill32
3
Fox 351 dipstick showing overfull?
  • 387lx
  • Feb 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
200
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 9, 2026
Noobz347
A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
Engine Gas in my oil
  • limp
  • Jun 15, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
35
Views
2K
Fox 5.0 Mustang Tech May 16, 2026
Mindseye007
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?