• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

oil pump gasket

  • Thread starter Thread starter stevesLX
  • Start date Start date Apr 11, 2007

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Apr 11, 2007
#1
  • Apr 11, 2007
  • #1
O.K. guys so what happens if you dont have a gasket between the oil pump and the block where it mounts?
 
Y

Yellowpnoy

New Member
Feb 6, 2006
203
0
0
Apr 11, 2007
#2
  • Apr 11, 2007
  • #2
Nothing much really, i didnt even use one. Use one or dont, not going to make much of a difference.

Anthony
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Apr 11, 2007
#3
  • Apr 11, 2007
  • #3
o.k. I have a high volume pump on a stock 302 and I didn't put the gasket on and I have some oiling issues that are making my lifters noisy.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Apr 11, 2007
#4
  • Apr 11, 2007
  • #4
Gaskets prevent leaks. You may have a leak between the pump housing and the engine block. The leak could either suck air from the crankscase or leak oil under pressure and squirt it onto the moving parts in the crankcase

Gaskets may be fabricated using the ball end of a small ball pien hammer. Place the gasket material on the part and tap around the part edges and holes. The sharp edges on most parts will cut the gasket material cleanly. An Exacto knife will clean up what the hammer didn't do neatly.
 
Y

Yellowpnoy

New Member
Feb 6, 2006
203
0
0
Apr 11, 2007
#5
  • Apr 11, 2007
  • #5
Are you building oil pressure?
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Apr 11, 2007
#6
  • Apr 11, 2007
  • #6
oil pressure thats out of this world. When I am on the interstate say 50 -70MPH my oil pressure is around 70-80 and if I run it hard its around 90-100 PSI When I idle its around 40-50PSI
 
Y

Yellowpnoy

New Member
Feb 6, 2006
203
0
0
Apr 11, 2007
#7
  • Apr 11, 2007
  • #7
Your oil pressure sounds great, probably just a bad lifter, did ou soak the lifters in oil before installing them in the motor? Are your seat pressures too high on the valve springs and causing the lifters to collapse?
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Apr 11, 2007
#8
  • Apr 11, 2007
  • #8
Not to sound rude but I have done and replaced everything possible within the valvetrain minus getting new heads. I have replaced 3 sets of lifters 2 sets of valve springs 3 differen't length pushrods, rockers, shims you name it its been changed or replaced. Its been to 3 differen't speed performance race shops and also the Ford dealer and nobody can figure it out. The only thing they all can think of is its the high volume oil pump causing it. They all say it needs just a standard pump on it. I have even ran 20/50 and lucas oil that thick crap in it and it doesn't sound any differen't. The car is quiet at idle but as soon as you rev it up or put it under any type od load thats when she starts ticking.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Apr 11, 2007
#9
  • Apr 11, 2007
  • #9
No clues as to what type of heads, rocker arms, cam or anything else in the engine. My crystal ball is in bad need of cleaning, so guessing doesn't do well for this type of problem.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Apr 11, 2007
#10
  • Apr 11, 2007
  • #10
Stock heads,303Fcam factory pedastal rockers and also have tried a set of aluminum rollers no difference.
 

bullitstang1313

Member
Jan 21, 2003
713
0
16
Indianapolis / Columbus, Indiana
Apr 11, 2007
#11
  • Apr 11, 2007
  • #11
Not to sound rude, but did you ever check piston to valve clearance. Maybe you have some interference, but only when the engine is warm and things expand. It seems like you have been fighting this issue for quite a long time. Are you sure it is in the valve train? What is the condition of the engine: stock block, rebuilt, stroker?
 
Y

Yellowpnoy

New Member
Feb 6, 2006
203
0
0
Apr 11, 2007
#12
  • Apr 11, 2007
  • #12
Like Bullitstang said, have you checked the piston to valve clearance? That could be your problem. I dont see how a high volume oil pump could cause this problem. Being that you changed basically everything else in the valvetrain minus that cam, that could be your problem. Did the shops that you took it to know that you had an F-cam in the car?

Anthony
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Apr 12, 2007
#13
  • Apr 12, 2007
  • #13
Yes they did and I even took it to another machine shop to have their work checked out and they said every thing was good. Its weird cause the car runs like a scolded dog but has that ticking that will drive you absolutely crazy. Now with that being said I got the oil pump changed and low and behold it has quieted down some but not totally.
 
Y

Yellowpnoy

New Member
Feb 6, 2006
203
0
0
Apr 12, 2007
#14
  • Apr 12, 2007
  • #14
One more thing, have you checked your header gaskets? If they leak they can make a sound that is almost identical to a lifter/valve tick. Check all your bolts and make sure they are tight and even take them off and look at the gaskets themselves, they are cheap enough and not that hard to change. Being that you said its coming from the rear towards the firewall, sometimes the bolts in the back can be hard to get to and you cant get enought torque on them. Also, the header bolts can loosen within a few miles after you have installed them and can cause a leak, you can go back and retighten them after a few miles. Just an idea!

Anthony
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Apr 12, 2007
#15
  • Apr 12, 2007
  • #15
yes as I read this post I was thinking the same as Yellowpony. A header leak could be the noise you are hearing. It may not be a leak at the header gasket itself. Sometimes depending on which brand headers you have the quality is a little shoody. There could be gaps in the weld between primary tubes where you are getting the ticking noise from.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Apr 12, 2007
#16
  • Apr 12, 2007
  • #16
O.K. I understand that but I had the headers off to pull the motor 2 days agq and put new gaskets on and unless there are gaps in the primarys I dont think I have a header leaking. The headers are brand new BBK full length which I know doesn't matter. I do know that if you take a stethescope and place it on the intake or valve covers you can hear it clear as day.
 

bluevenom867

I will have images of molesting stuffed animals in
Dec 15, 2003
1,704
1
0
St.Petersburg,FL
Apr 13, 2007
#17
  • Apr 13, 2007
  • #17
What kinda work has been done to the heads? Does it have stock guides and seats? What are the vavles? Does it feel like it doesnt have much power,backfire,pop,or hard to start?
 
Y

Yellowpnoy

New Member
Feb 6, 2006
203
0
0
Apr 13, 2007
#18
  • Apr 13, 2007
  • #18
I know that they are stock rockers, are you sure that the rocker arm is not hitting the valve covers? Are they stock valve covers? I am running out of things that could be causing this problem for you. From what you said with the stethoscope, sounds like its backfiring through the intake.

Anthony
 
You must log in or register to reply here.

Similar threads

Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
744
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
S
Engine Belt routing with supercharger and smog/ac/ps delete
  • Steve6482
  • Jul 15, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
158
Fox 5.0 Mustang Tech Jul 15, 2026
Steve6482
S
9
Forced Induction Prepping for supercharger on non-stock build
  • 91fox427
  • Nov 25, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
606
Fox 5.0 Mustang Tech Jan 5, 2026
Qtrhrse23
A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
D
Paint removal on machined gasket surfaces.
  • Ddyer2868
  • Feb 16, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
397
1965 - 1973 Classic Mustangs -General/Talk- Feb 23, 2026
ctandc
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?