• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Oxygen Sensor Removal??

  • Thread starter Thread starter Quick Pony
  • Start date Start date Dec 1, 2007

Quick Pony

Member
Nov 28, 2002
129
0
16
Pensacola, Florida
Dec 1, 2007
#1
  • Dec 1, 2007
  • #1
I bought 2 oxygen sensors for my 1991 LX, 5.0 convertible. I removed the old sensor on the driver's side and put the new one in, which took about 3 minutes.

The passenger side sensor is another story. I have tried for 2 days to remove it, with no success!! I have the special socket and I'm getting a good grip on the old one, it just won't budge. I have used PB Blaster lubricant on it, hit it with a hammer, still nothing.


Anybody have any tricks up their sleeve?

I have to replace it because the old one's wires are torn up.

What will happen if I drive the car with one new oxygen sensor and the other one
disconnected?

Thanks

Larry
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Dec 1, 2007
#2
  • Dec 1, 2007
  • #2
Hit the bung with a propane torch and get it nice and hot. Spray it with some type of penetrating oil while it's hot, and it will draw the cool oil into the threads. Yes, it will smoke to high hell and smell like a barbecue grill, but it works. It'll still take some effort to remove, but it'll be a lot easier than just fighting with it using the socket and oil.
 

5.0 Nostalgia

10 Year Member
Feb 28, 2003
904
5
39
CT
Dec 1, 2007
#3
  • Dec 1, 2007
  • #3
I just use a 7/8 wrench. If it's too tight, I just tap it. Unless you are using a breaker bar, the wrench will give you more leverage. I agree with the propane torch though, just be careful.
 

89-347-LX

New Member
Nov 17, 2007
38
0
0
Oklahoma
Dec 1, 2007
#4
  • Dec 1, 2007
  • #4
i had to use a small pipe wrench on mine and just keep loading it down with DW-40 and it finally came out but with hassle on every turn
 

Quick Pony

Member
Nov 28, 2002
129
0
16
Pensacola, Florida
Dec 1, 2007
#5
  • Dec 1, 2007
  • #5
Hey Matt,

Thanks for the reply. I was thinking the same thing about a torch, but unfortunately I don't have one. I thought there my be another method of removal that I had overlooked.

I just drove the car to the gas station to fill up and it runs pretty good with only 1 oxygen sensor working, but when I stop at a traffic light, its idle is erratic.

I've have never had such a problem removing a part in my entire life!!!!

Thanks again


Larry
 

Quick Pony

Member
Nov 28, 2002
129
0
16
Pensacola, Florida
Dec 1, 2007
#6
  • Dec 1, 2007
  • #6
Thanks guys for the replies. I'm going to keep trying till that sucker is out.


Larry
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Dec 1, 2007
#7
  • Dec 1, 2007
  • #7
You might be able to get away without a torch if you try it while the exhaust it hot from driving. I picked up a propane torch for like $10 from the local Ace Hardware in town by me. One word of caution though, your entire exhaust system is going to be damn hot if you do it after driving, versus just the one area when using the torch.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Dec 1, 2007
#8
  • Dec 1, 2007
  • #8
7/8" box end wrench and a 4# hammer (beating on the other end of the wrench). The shocking from the hammer-blows is like an impact wrench.

Good luck.
 
9

90bluegt

Founding Member
Dec 9, 1999
592
0
16
Dec 1, 2007
#9
  • Dec 1, 2007
  • #9
Hissin50 check your private messages...
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Dec 1, 2007
#10
  • Dec 1, 2007
  • #10
HISSIN50 said:
7/8" box end wrench and a 4# hammer (beating on the other end of the wrench). The shocking from the hammer-blows is like an impact wrench.

Good luck.
Click to expand...


I was going to buy an impact gun until i discovered that method. never had a problem with a bolt that that method couldn't free
 
9

90bluegt

Founding Member
Dec 9, 1999
592
0
16
Dec 1, 2007
#11
  • Dec 1, 2007
  • #11
I just use a wrench with another wrench hooked into it, plus the end of my jack (it's removable with a good size hole) and PB-Blast. That usually works..
 
You must log in or register to reply here.

Similar threads

Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
485
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
A
P0036 P0056 P0137 P0157 2020 Ford Mustang GT
  • AmkoA
  • Jun 16, 2026
  • 2024+ (S650) Mustang -General/Talk
Replies
0
Views
291
2024+ (S650) Mustang -General/Talk Jun 16, 2026
AmkoA
A
J
Exhaust manifold to Y-pipe nut & stud dimensions?
  • joeybuddy96
  • Jul 7, 2026
  • SN95 V6 Mustang Tech
Replies
2
Views
221
SN95 V6 Mustang Tech Jul 9, 2026
joeybuddy96
J
J
Fox Lost all gauge cluster function after Holley Terminator X install (solved)
  • Justin17383
  • Nov 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
256
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Friday at 3:09 PM
2000xp8
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
616
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?