• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

PCV pictures/setup?

  • Thread starter Thread starter Kabuki_notch
  • Start date Start date Jan 19, 2006

Kabuki_notch

Founding Member
Nov 19, 2001
670
394
113
Rochester, NY
Jan 19, 2006
#1
  • Jan 19, 2006
  • #1
I was wondering if anyone had any drawing or pictures of the PCV setup on a 5.0. I never totally understood the whole system and considering it's in such a tight spot its hard to screw around with it. Thanks in advance

-Rob
 

PuterAmI

Member
Mar 29, 2003
513
0
16
Madison, Alabama
Jan 19, 2006
#2
  • Jan 19, 2006
  • #2
Depends upon the year.

On my carbed when it was stock. the air draw starts in the round breather with a PCV filter. It's pulled into the right valve cover into the engine, back out at the left cover where the PCV valve resides in the breather cap, then to the base of the carburetor.

On the SEFI, it's drawn from the TB into the right valve cover, through the engine, then up through the back of the intake where there is a screen to hold back oil, then a PCV valve in a grommet. This leads into the bottom of the intake.
 

Kabuki_notch

Founding Member
Nov 19, 2001
670
394
113
Rochester, NY
Jan 19, 2006
#3
  • Jan 19, 2006
  • #3
would be a efi 86-93 setup
 

stangjunkie

New Member
Nov 15, 2004
381
0
0
Jan 19, 2006
#4
  • Jan 19, 2006
  • #4
pcv = positive crankcase ventalation basically it takes gasses in your crankcase....(gasoline, or any other vapor) and releases them through a check valve in your valve cover. those gasses are directed to your air intake (via hose) and burned with your intake gasses in the form of air
 

wild86stang

New Member
Oct 12, 2005
115
0
0
Milan, OH
Jan 19, 2006
#5
  • Jan 19, 2006
  • #5
Is there power to be gained from a crankcase evacuation system? I'm looking at the header-type system from Moroso for $60. It's listed as MOR-25900 at Summit. Would this work with the stock PCV system or would it defeat it? My main conern is that the power brakes have a vaccum assist so it would seem to me that it would be bad to lessen the vaccum to that.
 

wild86stang

New Member
Oct 12, 2005
115
0
0
Milan, OH
Jan 19, 2006
#6
  • Jan 19, 2006
  • #6
anybody?
 

PuterAmI

Member
Mar 29, 2003
513
0
16
Madison, Alabama
Jan 20, 2006
#7
  • Jan 20, 2006
  • #7
The power increase is miniscule. It's a way of having PCV without spoiling the intake mix.

AFAIK, keeping the rings sealed and keeping pressure from building up in the crankcase is what a PCV system is for - not power.
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jan 20, 2006
#8
  • Jan 20, 2006
  • #8
Contemporary PCV systems are part of the emissions system of the car -- as such the EPA had more to do with their design than anyone else.

Any engine builds crankcase pressure when it runs. Some blow by makes it past the rings, and each time a piston moves down in the bore it compresses the air in the crankcase underneath it. So there's lots of exhaust/unburned-hydrocarbons/vaporized-misted hot oil blowing around at a pretty good velocity inside the crankcase when the engine is running. That crankcase pressure has to be relieved or it will blow out seals and gaskets. Many a leaking rear main seal has nothing to do with a bad seal, and everything to do with a malfunctioning pcv system that is allowing crankcase pressure to build.

Back in the day, most engines just had a big pipe attached to the crankcase that hung down under the car. Wasn't uncommon to see them blowing 'smoke' out of it as they'd chug down the road.

The EPA decided that they didn't want that mess fouling the air -- and that was the beginning of the crankcase ventilation systems of today. Early systems were nothing more than a connection from the valve cover (i.e. - crankcase) to the air filter - with some filtering media to knock oil out of the air stream. This fed the nastiness being put out by the crankcase back into the engine to be combusted.

The next versions decided they could 'suck' the stuff out of the crankcase by letting manifold vaccum pull on it. The PCV system was born -- POSITIVE crankcase ventilation -- meaning, we're not gonna let it come out under it's own power, we're gonna suck it out of the crankcase. So pcv valves (a simple check valve) were installed in the valve cover, and a hose to the base of the carb provided a vacuum source. The pcv/check valve was necessary so that no air/fuel mixture from the carb could find it's way into the crankcase through the hose/valve cover. Crankcase explosions are nasty. So due to the pcv/check valve air could only move from the cover to the manifold, not the other way.

As sequential fuel injection came along on the 5.0's the new spot for accessing the crankcase was the back of the lower intake. A rubber grommet holds the pcv valve which connects to the upper intake manifold via hose. Below the grommet is a wire-mesh screen that acts as an oil trap -- designed to knock as much oil out of the crankcase flow as it can. The last part of the contemporary pcv system on the efi HO 5.0's is the little hose that runs from the throttle body to the valve cover oil filler neck nipple. When manifold vacuum sucks on the crankcase, eventually it's going to pull air INTO the crankcase from the outside. That air is going into the intake as part of the combustion air -- so in a mass air car it really needs to be metered air. And, if you don't allow a source for it -- we'll call it 'make up air' -- eventually you'll pull a vacuum on the crankcase; not what the designers wanted. That little hose between throttle body and valve cover provides a source of metered make-up air for the system. When vacuum is present in the intake, metered air (it's already passed through the maf) moves from the throttle body into the crankcase (via valve cover) to make up for the air being sucked from the crankcase via the pcv/manifold connection. At wide open throttle when there is no manifold vacuum, the same hose serves to help vent the crankcase if the pcv/valve/hose can't keep up with the volume the crankcase is producing. So the little hose between the throttle body and the valve cover is bi-directional.

When the oil trap/screen beneath the pcv valve becomes clogged, all the crankcase ventilation has to occur through that little throttle body hose. It's not uncommon for a bunch of oil to collect up in the throttle body/air inlet piping. That's a symptom of a clogged oil trap or clogged pcv valve. It's exacerbated when someone removes the oil baffle in the cover to clear 1.7 rockers with the stock covers...

Got it?
 

1993SSP

Founding Member
Sep 5, 2001
1,194
0
37
Ky
Jan 20, 2006
#9
  • Jan 20, 2006
  • #9
My screen under the PCV valve is gone, should it be there??
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jan 20, 2006
#10
  • Jan 20, 2006
  • #10
Read my post above yours -- what's your best guess?
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jan 20, 2006
#11
  • Jan 20, 2006
  • #11
SSP - keep in mind - you're supercharged. So the rules are completely different for you regarding crankcase ventilation. You can't have anything obviously that connects crankcase to manifold in a way that allows boost to enter the crankcase. The easy fix is to leave the pcv functional -- but upgrade the valve to one that will withstand your boost level; cap the throttle body line, and re-route a LARGER hose from the valve cover to a point in between your maf (assuming you're draw-through) and the suction side of the compressor.
 

bdazzgt

I had to jerk off the cable to get it to stop.
Dec 27, 2005
328
0
16
Springfield MO
Jan 20, 2006
#12
  • Jan 20, 2006
  • #12
Mike that write up kicked azz, very informative
 

1993SSP

Founding Member
Sep 5, 2001
1,194
0
37
Ky
Jan 20, 2006
#13
  • Jan 20, 2006
  • #13
The school of "Michael Yount" is now in session!

Im gonna take it the screen needs to be in there, what kind of valve would you reccomend?? One for a diff type car?? I am only running 6 pounds of boost, thanks
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jan 20, 2006
#14
  • Jan 20, 2006
  • #14
A lot of folks talk about running T'bird turbo valves or Supra turbo valves -- heresay I'm passing on; no direct experience for me being a 'boost' virgin...
 
You must log in or register to reply here.

Similar threads

Engine on3 Conversion to draw through MAF?
  • sav22rem22
  • Oct 11, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
373
Fox 5.0 Mustang Tech Oct 11, 2025
sav22rem22
Fox Cobra wheels real vs. replicas
  • keel
  • Nov 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
319
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 11, 2026
keel
G
Resolved Smoking Wiring Issue After GT40 Head Swap
  • Grapes
  • Aug 15, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
596
Fox 5.0 Mustang Tech Aug 22, 2026
Grapes
G
M
Resolved PCV Tube and Valve Cover Breather Hole Locations
  • MDrisc
  • Sep 11, 2024
  • Fox 5.0 Mustang Tech
Replies
3
Views
1K
Fox 5.0 Mustang Tech Sep 22, 2024
MDrisc
M
D
2006 GT Windshield Cowl install
  • Daddidio
  • Mar 12, 2026
  • 2005 - 2009 Specific Tech
Replies
0
Views
291
2005 - 2009 Specific Tech Mar 12, 2026
Daddidio
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?