• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Please Quick Answer

  • Thread starter Thread starter damystikal69
  • Start date Start date May 12, 2006
D

damystikal69

New Member
Apr 29, 2005
86
0
0
Wilmington, Oh
May 12, 2006
#1
  • May 12, 2006
  • #1
Iv'e got my car at Top Dead Center. I put the distributor in. Wheres the rotor sit? Is it torward the number 1 cylinder or is it the number one on the cap?
 

aleborjas

New Member
Sep 11, 2005
610
0
0
May 12, 2006
#2
  • May 12, 2006
  • #2
the number one on the cap, facing the intake
 

giddyup306

Founding Member
Oct 22, 2002
3,041
2
59
May 12, 2006
#3
  • May 12, 2006
  • #3
Under the 1# on the cap.
 
D

damystikal69

New Member
Apr 29, 2005
86
0
0
Wilmington, Oh
May 12, 2006
#4
  • May 12, 2006
  • #4
so,the rotor should be at 12:00 postion?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 12, 2006
#5
  • May 12, 2006
  • #5
Putting the distributor back in is fairly simple. Pull #1 sparkplug, put your finger in the sparkplug hole, crank the engine until you feel compression. Then line up the TDC mark on the balancer with the pointer on the engine block. Align the distributor rotor up with the #1 position marked on the cap, slide the distributor down into the block, (you may have to wiggle the rotor slightly to get the gear to engage) and then note where the rotor is pointing. If it still lines up with #1 position on the cap, install the clamp and bolt. If not, pull it out and turn 1 tooth forwards or backwards and try again. Put the #1 spark plug back in and tighten it down, put the clamp on the distributor, but don't tighten it too much, as you will have to move the distributor to set the timing. Note that if it doesn't align perfectly with #1 position, you can turn the distributor until it does. The only problem is that if you are too far one way or the other, you can't turn the distributor enough to get the 10-14 degree optimum timing range.

At this point hook up all the wires, get out the timing light and start the engine. Set the timing where your car runs best. Don't forget to disconnect the SPOUT jumper connector when you set the timing, and plug it back in when you finish.
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
May 12, 2006
#6
  • May 12, 2006
  • #6
if after you do that and the car doesn't start it is because dizzy is 180 degrees out. sometimes people don't get tdc on the compression stroke. jrichker gives you all you need to know. i have seen the Ford engineers put a dizzy in 180 degrees out. it happens to us all.
 
You must log in or register to reply here.

Similar threads

W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
308
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
349
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
Engine Hiccup at full throttle
  • keel
  • Jun 2, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
31
Views
1K
Fox 5.0 Mustang Tech Jul 30, 2026
keel
K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
404
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
342
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?