Poly tranny mount install??

DemonGT

Founding Member
May 24, 2002
871
51
49
Sparta,WI
i bought the poly tranny mount from energy suspension and it had the poly part and a attached metal plate on top that is not removable ...and then it came with another metal plate and i didnt know what it was for so left it out..but i looked at my 89 and it has the same mount and i seen the metal plate i left out goes on top of the other metal plate thats attached to the poly part....

my question is...what are the consequences of leaveing out that metal plate?
 
I would imagine it's fairly thin, so it really wouldn't throw off your driveshaft angle. May not cause any problems, but it's only 2 bolts and lift up on the trans a little to pop it in if there are any issues. I'd put it on if it called for it, as it may serve a purpose that we don't know
 
DemonGT said:
i bought the poly tranny mount from energy suspension and it had the poly part and a attached metal plate on top that is not removable ...and then it came with another metal plate and i didnt know what it was for so left it out..but i looked at my 89 and it has the same mount and i seen the metal plate i left out goes on top of the other metal plate thats attached to the poly part....

my question is...what are the consequences of leaveing out that metal plate?

I just put one in a few weeks ago, in the instructions it says you must use that plate and that it is not a spacer.

Hope that helps.
 
87GTSnake said:
I just put one in a few weeks ago, in the instructions it says you must use that plate and that it is not a spacer.

Hope that helps.

Yes you are correct! I just put one in along with the 2 crossmemebr polyurethane bushings and it does require that plate to be installed.
 
off subject but i also used the crossmemebr polyurethane bushings, but...i left that plate out...its not hard to put in so i suppose i should put it in regardless..but id still like to know why its there :rolleyes:
 
i dont know why its there. probably correct angle, pressure. whatever.

but i bought a poly mount kit also, and mine also has the plate, and says i must use the plate... so you're damn right im going to use it. i wouldnt take my chances otherwise.
 
If that plate sits in direct contact with the poly-urethane then it's probably there to disperse the load and keep the poly from tearing and squeezing itself through the bolt holes etc..
 
here is a pic of the mount i have...the plate below the poly mount is what i left out...

ens-4-1104r_w.webp
 

Attachments

  • ens-4-1104r_w.webp
    ens-4-1104r_w.webp
    8.8 KB · Views: 165
I always figured it was to sort of "pre-load" tension onto the mount. If you lay one atop the other, they don't just lay perfectly flush together - there's almost 1/8" gap between the ends of the two, and it's snug enough that you can't just squeeze 'em together by hand. (Well, unless you've got some supa-dupa finger strength...) Kinda confused me a bit, too, when I got mine; I thought it was some kinda adapter for early-year 'Stangs or something.

Not to hijack, but I've also noticed that no matter how I go about setting up the crossmember during install, the two bottom holes of my mount are always off to one side by almost 1/4". I have to poke a phillips screwdriver up into one hole and pry the sucker over to get the holes to line up enough that I can get one bolt in. That, and I had to get creative with a grinder and a big drill bit to widen the crossmember holes to make those fatter bolts actually poke through there. Anyone else had the same?
 
Darkwriter77 said:
I always figured it was to sort of "pre-load" tension onto the mount. If you lay one atop the other, they don't just lay perfectly flush together - there's almost 1/8" gap between the ends of the two, and it's snug enough that you can't just squeeze 'em together by hand. (Well, unless you've got some supa-dupa finger strength...) Kinda confused me a bit, too, when I got mine; I thought it was some kinda adapter for early-year 'Stangs or something.

Not to hijack, but I've also noticed that no matter how I go about setting up the crossmember during install, the two bottom holes of my mount are always off to one side by almost 1/4". I have to poke a phillips screwdriver up into one hole and pry the sucker over to get the holes to line up enough that I can get one bolt in. That, and I had to get creative with a grinder and a big drill bit to widen the crossmember holes to make those fatter bolts actually poke through there. Anyone else had the same?

How many times have you had to set up the crossmember? I havent experienced this problem. Finally something that is NOT wrong with my stang.:cheers:
 
Daggar said:
If that plate sits in direct contact with the poly-urethane then it's probably there to disperse the load and keep the poly from tearing and squeezing itself through the bolt holes etc..
:stupid:
darthcual said:
That is definately a load dispersment plate and I agree 100% with daggar. Without it, it will probably tear up eventually.
:stupid:

It spreads the loads. With out it I would bet things get shreaded after only a couple of hard launches.

:OT: I have never had the transmission line up easily with all of the exhaust and mounting brackets. It is always a pain in the @$$. Best I have found is using the short end of a 90* Allen wrench to get the holes of all the plates to line up.
Hope that can help.

jason