• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Poly tranny mount install??

  • Thread starter Thread starter DemonGT
  • Start date Start date Oct 15, 2005

DemonGT

Founding Member
May 24, 2002
871
51
49
Sparta,WI
Oct 15, 2005
#1
  • Oct 15, 2005
  • #1
i bought the poly tranny mount from energy suspension and it had the poly part and a attached metal plate on top that is not removable ...and then it came with another metal plate and i didnt know what it was for so left it out..but i looked at my 89 and it has the same mount and i seen the metal plate i left out goes on top of the other metal plate thats attached to the poly part....

my question is...what are the consequences of leaveing out that metal plate?
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Oct 15, 2005
#2
  • Oct 15, 2005
  • #2
I would imagine it's fairly thin, so it really wouldn't throw off your driveshaft angle. May not cause any problems, but it's only 2 bolts and lift up on the trans a little to pop it in if there are any issues. I'd put it on if it called for it, as it may serve a purpose that we don't know
 

87GTSnake

Member
Mar 31, 2005
96
0
6
PA
Oct 16, 2005
#3
  • Oct 16, 2005
  • #3
DemonGT said:
i bought the poly tranny mount from energy suspension and it had the poly part and a attached metal plate on top that is not removable ...and then it came with another metal plate and i didnt know what it was for so left it out..but i looked at my 89 and it has the same mount and i seen the metal plate i left out goes on top of the other metal plate thats attached to the poly part....

my question is...what are the consequences of leaveing out that metal plate?
Click to expand...

I just put one in a few weeks ago, in the instructions it says you must use that plate and that it is not a spacer.

Hope that helps.
 

Realmongo

I prefer to be called "Evil Genius"
Founding Member
Oct 10, 2001
2,466
86
99
Western Mass
Oct 16, 2005
#4
  • Oct 16, 2005
  • #4
87GTSnake said:
I just put one in a few weeks ago, in the instructions it says you must use that plate and that it is not a spacer.

Hope that helps.
Click to expand...

Yes you are correct! I just put one in along with the 2 crossmemebr polyurethane bushings and it does require that plate to be installed.
 

DemonGT

Founding Member
May 24, 2002
871
51
49
Sparta,WI
Oct 16, 2005
#5
  • Oct 16, 2005
  • #5
off subject but i also used the crossmemebr polyurethane bushings, but...i left that plate out...its not hard to put in so i suppose i should put it in regardless..but id still like to know why its there
 

dderek

New Member
Feb 29, 2004
180
0
0
Oct 16, 2005
#6
  • Oct 16, 2005
  • #6
i dont know why its there. probably correct angle, pressure. whatever.

but i bought a poly mount kit also, and mine also has the plate, and says i must use the plate... so you're damn right im going to use it. i wouldnt take my chances otherwise.
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Oct 16, 2005
#7
  • Oct 16, 2005
  • #7
If that plate sits in direct contact with the poly-urethane then it's probably there to disperse the load and keep the poly from tearing and squeezing itself through the bolt holes etc..
 

Mavrick

Founding Member
Aug 29, 2002
2,264
0
46
Collingwood, ON
Oct 16, 2005
#8
  • Oct 16, 2005
  • #8
Does anyone have a picture of what this plate is? I'm trying to remember if i included it with mine..
 

DemonGT

Founding Member
May 24, 2002
871
51
49
Sparta,WI
Oct 17, 2005
#9
  • Oct 17, 2005
  • #9
here is a pic of the mount i have...the plate below the poly mount is what i left out...

 

Attachments

  • ens-4-1104r_w.webp
    8.8 KB · Views: 165

Darkwriter77

Resident Ranting Negative Nancy
5 Year Member
Jul 1, 2005
315
283
134
Apache Junction, AZ
Oct 18, 2005
#10
  • Oct 18, 2005
  • #10
I always figured it was to sort of "pre-load" tension onto the mount. If you lay one atop the other, they don't just lay perfectly flush together - there's almost 1/8" gap between the ends of the two, and it's snug enough that you can't just squeeze 'em together by hand. (Well, unless you've got some supa-dupa finger strength...) Kinda confused me a bit, too, when I got mine; I thought it was some kinda adapter for early-year 'Stangs or something.

Not to hijack, but I've also noticed that no matter how I go about setting up the crossmember during install, the two bottom holes of my mount are always off to one side by almost 1/4". I have to poke a phillips screwdriver up into one hole and pry the sucker over to get the holes to line up enough that I can get one bolt in. That, and I had to get creative with a grinder and a big drill bit to widen the crossmember holes to make those fatter bolts actually poke through there. Anyone else had the same?
 

darthcual

Member
Mar 31, 2005
985
19
18
Arlington, TX
Oct 18, 2005
#11
  • Oct 18, 2005
  • #11
That is definately a load dispersment plate and I agree 100% with daggar. Without it, it will probably tear up eventually.
 

darthcual

Member
Mar 31, 2005
985
19
18
Arlington, TX
Oct 18, 2005
#12
  • Oct 18, 2005
  • #12
Darkwriter77 said:
I always figured it was to sort of "pre-load" tension onto the mount. If you lay one atop the other, they don't just lay perfectly flush together - there's almost 1/8" gap between the ends of the two, and it's snug enough that you can't just squeeze 'em together by hand. (Well, unless you've got some supa-dupa finger strength...) Kinda confused me a bit, too, when I got mine; I thought it was some kinda adapter for early-year 'Stangs or something.

Not to hijack, but I've also noticed that no matter how I go about setting up the crossmember during install, the two bottom holes of my mount are always off to one side by almost 1/4". I have to poke a phillips screwdriver up into one hole and pry the sucker over to get the holes to line up enough that I can get one bolt in. That, and I had to get creative with a grinder and a big drill bit to widen the crossmember holes to make those fatter bolts actually poke through there. Anyone else had the same?
Click to expand...

How many times have you had to set up the crossmember? I havent experienced this problem. Finally something that is NOT wrong with my stang.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Oct 18, 2005
#13
  • Oct 18, 2005
  • #13
Daggar said:
If that plate sits in direct contact with the poly-urethane then it's probably there to disperse the load and keep the poly from tearing and squeezing itself through the bolt holes etc..
Click to expand...

darthcual said:
That is definately a load dispersment plate and I agree 100% with daggar. Without it, it will probably tear up eventually.
Click to expand...


It spreads the loads. With out it I would bet things get shreaded after only a couple of hard launches.

:OT: I have never had the transmission line up easily with all of the exhaust and mounting brackets. It is always a pain in the @$$. Best I have found is using the short end of a 90* Allen wrench to get the holes of all the plates to line up.
Hope that can help.

jason
 
You must log in or register to reply here.

Similar threads

D
Question about EGR valve, replacement, and a part on the valve.
  • DPP
  • May 9, 2026
  • SN95 V6 Mustang Tech
Replies
1
Views
271
SN95 V6 Mustang Tech May 23, 2026
DPP
D
Strut Tower Help!
  • 93Nifty
  • Jan 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
28
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 28, 2026
General karthief
M
1991 GT cigarette lighter/port not working (horn is working)
  • MartinM
  • Aug 29, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
339
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2025
MartinM
M
S
Car shakes when taking off help???
  • STANKYstangs
  • May 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
12
Views
553
1996 - 2004 SN95 Mustang -General/Talk- May 27, 2026
LILCBRA
S
Drivetrain 8.8 Pinion and 302 rear main seal leaks after replacing. 93 5.0 with t-5
  • Steigy4827
  • Jun 23, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
884
Fox 5.0 Mustang Tech Apr 1, 2026
Steigy4827
S
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?