• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Power Combo

  • Thread starter Thread starter OVRSTR89
  • Start date Start date Aug 22, 2005
O

OVRSTR89

New Member
Aug 19, 2005
2
0
0
Aug 22, 2005
#1
  • Aug 22, 2005
  • #1
If i run the trick flow track heat kit with my 347 stroker 70mm throttle body and 190lph fuel pump what injectors should i run and at abought what fuel pressure would be a good starting point. I know on all other injected cars run 50 to 60 psi and that is normal. But i figure the injector size if needing to be larger may be a lower pressure like 40psi. Thanks any information is appreciated.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Aug 22, 2005
#2
  • Aug 22, 2005
  • #2
I would suggest running 24lb injectors. This is assuming the power output will be about 300hp. If you have plans of boost in the immediate future then 30lb may be more appropriate, maybe bigger depending on boost levels.

I did use an excel calculator that I wrote to come up with this (I am not just making up numbers). If you would like to see it post your email or pm me, this site is not friendly to tables and it is a real pain to format it into Word. If you are not familiar with excel though it may just be confusing.


The fuel pressure should be fairly close to 40psi. I would set it to 39psi and try to tune from there. You just have to get close enough to correct so that the computer can adjust fuel ratio with injector duration.

The Ford systems seem to be about 39psi, other makes might go 50-60, but not many Mustangs should need that much pressure. Maybe very high compression or boost?

Come back if you still have questions

Good Luck
jason
 

Grn92LX

Fidanza Man!
Founding Member
Jan 14, 2001
6,819
64
129
New York
Aug 22, 2005
#3
  • Aug 22, 2005
  • #3
You want 30lb injectors and run 39psi with the vacuum line off. I wouldn't use a trickflow cam in a 347.
 

QDRHRSE

New Member
Dec 31, 2002
1,590
0
0
Palmdale, CA
Aug 22, 2005
#4
  • Aug 22, 2005
  • #4
Without reading the other posts I'd say 36's or 30's maybe. It depends on how much cam you end up with. If you end up with big high reving cam you might be right between 30-36. I guess it depends on your compression ratio and the total HP your gonna make. How much porting....etc. etc.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Aug 22, 2005
#5
  • Aug 22, 2005
  • #5
Anyone have a hp estimate from a dependable surce for this combo. The only formulas I have found for determining injector size are based upon hp levels. It's kinda tough to know the power level without putting the motor together and hitting a dyno.

What is the advertised power for the TrickFlow kit? Even if they only supply numbers for a stock 302, that would be fine.

I would love to run the numbers for you, but I need some power estimates first.

I agree that the TrickFlow cam may not be enough for the stroker, but I don't have any recommendations at the moment (I am just getting into cam design as of last night).

 
You must log in or register to reply here.

Similar threads

D
Fuel Erratic Fuel Pressure 1985 GT
  • DienstXIV
  • Jan 14, 2026
  • Fox 5.0 Mustang Tech
Replies
16
Views
939
Fox 5.0 Mustang Tech Jan 16, 2026
AeroCoupe
M
01 mustang 3.8 fuel pressure issue
  • Mhaley2006
  • May 29, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
530
1996 - 2004 SN95 Mustang -General/Talk- Aug 9, 2026
JohnKay
J
T
Fuel P0193 on a 2003 3.8 v6
  • Treemaster5000
  • Aug 18, 2026
  • SN95 V6 Mustang Tech
Replies
0
Views
122
SN95 V6 Mustang Tech Aug 18, 2026
Treemaster5000
T
1
Engine 91 mustang 302 Low acceleration car backfires pops and acts like it doesn’t want to take fuel
  • 1991Fox5.0
  • Oct 4, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Oct 6, 2025
1991Fox5.0
1
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
698
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?