Power Loss when warm :/

Synned

took tubgirl on a date and got banned
Mar 31, 2005
991
1
0
Philly
My car feels like a slug when it gets hot and I try to take off. It feels like I'm giving it 1/4 throttle although im all the way down. When the air is cool or the engine just started it runs amazing. It takes about 10 miutes on a hot day and like 30 when its cold, so its not the o2's.
Things I have done are:
Replaced plugs, wires, dizzy cap, rotor, ECT, o2's, cleaned MAF and IAT.
I have no codes.
Other threads like this they it seems like they just throw parts at it untill they find the missing link. It's a 95 AODE. I was thinking about:
Checking fuel pressure when it starts happening, and in my head some possible suspects are, TFI, IAT, MAP. I pass the cylinder balance test with 99. This has been going on for like 3 months. :-/. Anything you guys can suggest will be great.
 
ninety15.0 said:
your sayin that it feels like you are getting 1/4 throttle power when you take off but you are actually flooring it?? how many miles on the car?
Well I was kind of exaggerating. It feels slow from a takeoff but when I hit 3k rpms it starts pulling hard. I can easily break the tires loose when its running correctly, and im nowhere near that when its running incorrectly.
 
Does it seem to lose power above 3000 RPM when warm? If so, replace the TFI module. Check the TFI wiring for loose connections, corrosion and damaged wiring.
 
map

Map/bap.... Absolutly ... check your the hertz on your sensor... Which i believe in 95 was part of the mass air... i dont know where abouts you may be but here in new jersey around the toms river area we usually see about 158 to 206 hertz on the baro reading around here....
 
I was also thinking the MAP because the car does feel real bad when its humid outside, thats exactly what the MAP sensor reads right pressure of the atmosphere?
 
A failing MAP sensor wil usually set code 22.

Code 22 MAP (vacuum) or BARO signal out of range. The MAP or BARO sensor is pretty much the same sensor for both Mass Air & Speed Density cars. The main difference is where it is connected. Mass Air cars vent it to the atmosphere, while Speed Density cars connect it to the intake manifold vacuum. Its purpose is to help set a baseline for the air/fuel mixture and changes in barometric pressure. The MAP or BAP sensor puts out a 5 volt square wave that changes frequency with variations in atmospheric pressure. The base is 154 HZ at 29.92" of mercury - dry sunny day at sea level, about 68-72 degrees. You need an oscilloscope or frequency meter to measure it.

Baro or MAP test using frequency meter - run the test key on engine off. The noise from the ignition system will likely upset the frequency meter. I used a 10 x oscilloscope probe connected from the frequency meter to the MAP/BAP to reduce the jitter in the meter's readout.

If it is defective, your air/fuel ratio will be off and the car’s performance & emissions will suffer
 
jrichker said:
I think you are right on this one. I checked the Autozone diagrams and didn't see an external MAP/BAP Sensor. I haven't had much opportunity to spend time working on the 94-95 stangs like I have with the older ones.

Autozone diagram for 94-98 cars - http://www.autozone.com/servlet/UiB..._us/0900823d/80/1d/db/3c/0900823d801ddb3c.jsp
If I toss enough dung against the barn wall, something will stick. :D

Synned, what is your air intake and air filter set up? On the SN's, heat saturation is more of an issue than on foxes, IMHO. And fan wash is a real issue on SN's given the tight confines.

And do you know if your IAT is indexed? Given its relative location, I think it is important to keep it so (so = indexed). And it takes like 30 seconds to do.

I am sure nothing I said will help, but the stuff is easy/free and when I am stumped, I have to go back and redo things I did before and sometimes I see something or I happen to fix or jostle (sp) a connection, etc, which makes a difference.

Good luck.