Project "BlackOut" 89 convert.

[95BlueStallion]

its ok man. i just did mark Vii rotors up front for now. imma wait till my firend totales her 2001 GT....again its only a matter of time and steal the front of it.


imma have lynn merge the threads soon for me

Lol, but you forget that she will run over a couple curbs and then smash into a brick wall completely demolishing any usable parts on the front of the car. Just make sure she wears her seatbelt at all times! Ill check back tomorrow evening to see if you get that rear back on the car.

 

[ryan218]

Lol, but you forget that she will run over a couple curbs and then smash into a brick wall completely demolishing any usable parts on the front of the car. Just make sure she wears her seatbelt at all times! Ill check back tomorrow evening to see if you get that rear back on the car.

lol dont say that!!! thats where shes wrecked it twice so far!!!

im hoping. =[ im getting pissey cuz i wanna see it done lol

 

[Jaswir]

you can sell the rear to me and you will be able to pay your tickets

 

[ryan218]

you can sell the rear to me and you will be able to pay your tickets

im already 500 into my lawyer.

 

[ryan218]

now 5 lug swap is almost done. only thing left to do its put the drums back together and new hard lines on top of axle.

 

[Beasty306GT]

 

[SVT32VDOHC]

Looks like you got the bolts, but 50resto has them too. It would have been a good idea to do some LCA's while you were under there. My notch had BAD wheel hop with the stockers because the bushings were shot.

 

[ryan218]

Looks like you got the bolts, but 50resto has them too. It would have been a good idea to do some LCA's while you were under there. My notch had BAD wheel hop with the stockers because the bushings were shot.

yeah i wanted to but i just wanted to get this done for now. quad shocks are shot so im not even going to bother putting them back on.
get my pm?

 

[MAC'n89Blckstng]

Check out my low profile tires mang. That ish is tight son!

 

[95BlueStallion]

Good job man. Now just get the wheels on that match the front and go for a spin. That is, only around the block, and only once your brakes work...

 

[ryan218]

Check out my low profile tires mang. That ish is tight son!

im selling the bullets. i just threw them on there for the hell of it real quick they were burnout wheels.

 

[ryan218]

Good job man. Now just get the wheels on that match the front and go for a spin. That is, only around the block, and only once your brakes work...

eh man. no rear breaks. plug the line. its like have line lock right

lol
yeah picking up the wheels tomm and ill get them mounted...the drums are a nightmare i dont know what gose where

 

[riceslayer302]

coming along good ryan, i wish i had seen that you needed LCA bolts i had a few kicking around

 

[ryan218]

one thing after another. get the drivers side breaks on and put the wheel on. get to last lug crank it dont and i knew i ****ed up and grabed a bad lug. (stripped) and of course. ****ing stiped the stud! lug wont come off. i put a huge damn nick in the paint because i was frustrated and now im just pissed. time to call it a night.

any tips how to get it off? i put pressure behide it but it dose nothing

 

[stykthyn]

ummm dont you have ranger rotors? just get a new one.

 

[ryan218]

ummm dont you have ranger rotors? just get a new one.

there axles? and thats not a problem in doing. either way i still have to get the stripped pos off and out.

 

[stykthyn]

ohh, I forgot you are doing the rears now

 

[foxmustangman]

Can't you use an impact wrench? That sucks. A kid did that to another kids car in Auto Tech...he was PISSED! Yeah, i think an impact wrench should work fine.

 

[Beasty306GT]

get a smaller wrench and pound it on with a hammer and use an impact gun

 

[ryan218]

no. like the threads are ****ed up. it jusr spins on the eedge of the stud. losening and tighten. try prying behide it. nothing. im just going to go get a cut off whel and cut the stud.