• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

question for jrichker

  • Thread starter Thread starter jammer84_03
  • Start date Start date Sep 27, 2006

jammer84_03

New Member
Nov 30, 2003
468
1
0
Sep 27, 2006
#1
  • Sep 27, 2006
  • #1
ok, power window question. do you have a schematic for the power windows. i had my driver side window just completely stop working, it wasnt slow or anything before it happened, although i just did a tint job and the door panel apart. i might have possibly jolted a wire loose and it took a mth for the wire to come out somewhere. i havent taken it apart to check it yet, but is there and easy way to test my window motor, switch, and the wiring to track down my problem before i start going and ordering parts? thx for the help - james
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Sep 27, 2006
#2
  • Sep 27, 2006
  • #2
Sorry I'm not jrichker like you asked for, but here's the link.

http://www.veryuseful.com/mustang/tech/engine/images/mustang87-92 PowerWindowWiring.gif
 

jammer84_03

New Member
Nov 30, 2003
468
1
0
Sep 27, 2006
#3
  • Sep 27, 2006
  • #3
thx....that will get me started.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
33
129
Sep 27, 2006
#4
  • Sep 27, 2006
  • #4
When you hit the switch for the window, does the voltmeter drop any? Probably not. Check the switch connector in the door panel.

Good luck.
 

jammer84_03

New Member
Nov 30, 2003
468
1
0
Sep 27, 2006
#5
  • Sep 27, 2006
  • #5
ya...tonight once i get out of work i will test all the theories out. i knew this prob would arise sooner or later...this is the week of nickel dime stuff, the pass side door lock froze in the unlocked position, the driver side window wont open, and on the way to work this morning, the complete pass rear brake assembly came apart. got out to look at it and there were no brake pads!...lol and those were tightened to spec. also i think my axle bearings are going out. when i take off from a stop and sometime when i shift into the next gear from a roll i hear a popping noise from the rear end, might be the u-joints or bushings...not sure til i look.
 
You must log in or register to reply here.

Similar threads

Electrical ’86 Mustang – Power Windows/Locks Dead After Terminator X Swap
  • 5.0 Mike
  • Aug 21, 2025
  • Fox 5.0 Mustang Tech
Replies
0
Views
183
Fox 5.0 Mustang Tech Aug 21, 2025
5.0 Mike
Electrical Fried my window motor…
  • AnthonyA1234
  • Oct 25, 2024
  • Fox 5.0 Mustang Tech
Replies
8
Views
366
Fox 5.0 Mustang Tech Oct 26, 2024
General karthief
1999 Mustang GT - No Start- Need help understanding the fuel pump circuit and how it works
  • 99gtGuy
  • Nov 4, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
477
1996 - 2004 SN95 Mustang -General/Talk- Nov 7, 2025
04newedge-
0
Resolved Ignition switch questionable
  • Dontknowchit
  • Mar 14, 2025
  • Fox 5.0 Mustang Tech
Replies
13
Views
655
Fox 5.0 Mustang Tech Jun 18, 2025
General karthief
M
Too much for me to repair in my current housing situation
  • My Drama Magnet 04 Gt
  • Apr 1, 2026
  • The Welcome Wagon
Replies
8
Views
250
The Welcome Wagon Apr 14, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?