• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Quick A/C flush question.....Jrichker or anyone else

  • Thread starter Thread starter Black1987Stang
  • Start date Start date Apr 28, 2009

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Apr 28, 2009
#1
  • Apr 28, 2009
  • #1
I'm putting a/c back in my car after a few years of not having it, I had taken the lines off 2-3 years ago when I did my motor swap and I left the lines off the evaporator unplugged and want to clean it out in case any dirt, dust got in there...I had rinsed it out with a garden hose and steam cleaner and blew it out with compressed air to get the big stuff (was my only idea before I bought the flush solvent), now I want to get the remainder and get it dry in there....How can I rinse it out? I bought a can of ac flush from advance so I just pour it in the top line and let it run out the bottom and run compressed air to the top one till just air comes out the bottom? .....I'll have a vacuum pump soon but I have all new lines, dryer, condensor and dont want to contaminate them with the junk from the evap by sucking down a vacuum in the complete system....sooo I just need to clean out the evaporator alone, should I just use that flush and compressed air?
thanks
 

backfocus

Member
Sep 3, 2004
254
3
18
Little Rock, AR
Apr 28, 2009
#2
  • Apr 28, 2009
  • #2
A good simple way is to use a flush gun such as the one below.




You can use Mineral Spirits or a commercial flush solvent.

Spray it in one end and hold a rag over the other, this helps create some pressure to force out any particles, letting the rag loose after a few sprays. Do this a couple of times then switch sides and flush the other direction. An lastly if you have access to some Nitrogen, you can do a final flush with that to help remove any left over flushing agent.

Since you are using something that you are pouring you could pour a little in then, use nitrogen to force it out the other side. You could use air, but only if it is filter dried. I don't like putting anymore moisture into a system than I have to and that is what will happen if you use unfiltered compressor air.

Also don't take the caps off the new dryer until you are about to install in, just 10 minutes of it exposed to the air can render one useless.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Apr 28, 2009
#3
  • Apr 28, 2009
  • #3
Backfocus's advice is excellent. Follow it if at all possible.

Water is death to A/C systems , so I hope that you got all the water out. Flush the system with mineral spirits with some 91% alcohol added to remove any last traces of moisture.

The Ford systems use a orfice tube in place of an expansion valve or capillary tube. It resides in the high pressure feed line that comes from the condenser up front of the radiator and connects to the evaporator in the passenger compartment. It is not replaceable, so if it clogs, you replace the high pressure feed line. Some models may have the orfice tube in the inlet to the evaporator core.

My current vacuum pump is a refrigerator hermetic unit (motor & compressor in one unit). It was a freebe from a local used appliance store. I bolted it down to a piece of plywood & soldered a 1/4" flare fitting on the suction line. It works great, pulls 29" of vacuum in about 10 minutes or less. I have used it several times and have had excellent results.




See the link in my sign for R134 conversion and A/C charge instructions.
 
You must log in or register to reply here.

Similar threads

Engine A/C QUESTION
  • Mindseye007
  • Jun 5, 2025
  • Fox 5.0 Mustang Tech
  • 2 3 4
Replies
60
Views
2K
Fox 5.0 Mustang Tech Jun 22, 2026
nicholase
M
Progress Thread mnky99 2001 V6 evap core, ac compressor, heater core replacement
  • mnky99
  • Sep 5, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
530
1996 - 2004 SN95 Mustang -General/Talk- Sep 5, 2025
mnky99
M
B
Saying Hi
  • BriansNSane
  • Dec 20, 2025
  • The Welcome Wagon
Replies
5
Views
305
The Welcome Wagon Dec 21, 2025
BriansNSane
B
E
2007 GT Stalls when lights or a/c turned on
  • ejscarfo
  • Jun 22, 2026
  • 2005 - 2009 Specific Tech
Replies
2
Views
148
2005 - 2009 Specific Tech Jun 29, 2026
ejscarfo
E
S
Fuel ‘88 GT Runs Rich Cold — Fixes Itself When I Unplug Sensors (ECT, MAF, O2, etc.)
  • Sufarry
  • Nov 6, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
886
Fox 5.0 Mustang Tech Nov 9, 2025
Mustang5L5
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?