• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Replacing Side windows (both) info??

  • Thread starter Thread starter bloopbloob
  • Start date Start date Dec 23, 2007

bloopbloob

Member
Sep 27, 2006
578
4
16
Alberta
Dec 23, 2007
#1
  • Dec 23, 2007
  • #1
i need to replace my side windows (main and rear 1/4), and wondering what i have to do to get this done? any info or links would be greatly appreciated
 

Roland69

Sergeant Tangnet
Sep 17, 2005
2,867
3
58
Port Elgin, Ontario
Dec 23, 2007
#2
  • Dec 23, 2007
  • #2
easy job. Take the interior pannels around the rear quarter windows out and remove the small (I think 10mm) nuts and slowly peel the window out. Make sure you have all nuts (i think there is 7 per window) off before trying. the sealant should stay with the window and you may be able to reuse it. I would try and refinish a set to look like new ones before installing them.
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Dec 24, 2007
#3
  • Dec 24, 2007
  • #3
on your quarter glass don't try to reuse the butyl tape it will only cause a leak you want to get 5/16 butyl tape (aka windshield ribbon) and put that on your new window. now the door glass will be a bigger pain because Ford uses rivets to hold the glass onto the brackets(about the same style that hold your door handles on) you will need to knock the centers out then drill the rivet out to get the door glass insulators off the track work then reassemble and use rivets or bolts to put back together (wear safety glasses I did auto glass for 5 years you never know with tempered pieces)
 

04sleeper

Founding Member
Jun 22, 2002
2,674
14
89
Dallas, TX
Dec 24, 2007
#4
  • Dec 24, 2007
  • #4
For the door window, you will have to remove the door panel. Here's from off the top of my head:
1) Unscrew and remove the triangle plastic panel by the mirror. (Phillips Head)
2) Unscrew and remove the plastic door handle cup. (Phillips Head)
3) Unscrew and remove the window switch panel and unplug. (Phillips Head)
4) Unscrew top screw on armrest behind window switch panel. (Phillips Head)
5) Pop off the plugs (2) on the bottom of the armrest with a small flathead screwdriver.
6) Remove the bolts (2- 10mm IIRC) from the bottom of the armrest with a socket and extension.
7) Carefully pry the door panel clips away from the door with either a clip remover or a large flathead screwdriver.

8) Pull the door panel off from the top pushing upwards after all the clips are loose.
9) Peel away the plastic so you can access the inside of the door and get to the bolts for the window.
10) Remove the bolts and vacuum all the glass out of the inside of the door.
11) Replace the window by carefully sliding it down into the door and bolting it to the slider track.
12) Replace the door panel in reverse order.



For the rear window, you will have to remove the rear quarter panel to access the bolts.

The easiest way I have found to remove the rear window is to slowly pry the molding away with a small screwdriver just enough to put a coat hanger through the glue from the inside to the outside of the car.

Then have a friend help out pulling the coat hanger (or thin wire) back and forth to saw through the glue to help get it off the car.

Hope this helps a little.
 

Attachments

  • h18187650p.webp
    13.2 KB · Views: 157

04sleeper

Founding Member
Jun 22, 2002
2,674
14
89
Dallas, TX
Dec 24, 2007
#5
  • Dec 24, 2007
  • #5
PUNISHER RACING said:
on your quarter glass don't try to reuse the butyl tape it will only cause a leak you want to get 5/16 butyl tape (aka windshield ribbon) and put that on your new window. now the door glass will be a bigger pain because Ford uses rivets to hold the glass onto the brackets(about the same style that hold your door handles on) you will need to knock the centers out then drill the rivet out to get the door glass insulators off the track work then reassemble and use rivets or bolts to put back together (wear safety glasses I did auto glass for 5 years you never know with tempered pieces)
Click to expand...
+1 on getting a new seal.

Are the windows riveted onto the slider? I haven't done this in quite sometime but I thought it was bolted the last time I did one.
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Dec 24, 2007
#6
  • Dec 24, 2007
  • #6
They came factory riveted to the plastic slide, if it was replaced I bet it was bolted we had these gromets that popped in the glass like the insulators and used a big thick sheet metal screw to hold the glass to the track work.
 

bloopbloob

Member
Sep 27, 2006
578
4
16
Alberta
Dec 24, 2007
#7
  • Dec 24, 2007
  • #7
thanks for the help! so i'm guessing this is going to be a pain to do (especially with the butyl) outside in -15*C weather. ah well.... Should i get a heat gun to help seal the new butyl tape, or will it seal it when its that cold?
 

04sleeper

Founding Member
Jun 22, 2002
2,674
14
89
Dallas, TX
Dec 24, 2007
#8
  • Dec 24, 2007
  • #8
A heat gun will probably make the sealant more pliable and easier to mold.
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Dec 24, 2007
#9
  • Dec 24, 2007
  • #9
apply it inside then run out and pop it in just run your bolts down evenly to pull the sealant down nice and even, I used to use my cordless drill and set the torque setting fairly low. run em down a bit then get out the car and push it down some and then tighten some more till it is flat on the body. don't try to hog it all at once or it will pop the window. I almost forgot when putting on your butyl on your quarter glass put your seam(stop/start) at the bottom!!!
 
You must log in or register to reply here.

Similar threads

D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
207
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
Electrical Lincoln Mark VIII Replacement Fan Motor
  • AeroCoupe
  • Sep 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
168
Fox 5.0 Mustang Tech Sep 26, 2026
AeroCoupe
Brakes Front Brake Hardline Routing
  • 93Nifty
  • Sep 11, 2026
  • Fox 5.0 Mustang Tech
Replies
11
Views
409
Fox 5.0 Mustang Tech Oct 11, 2026
limp
J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
340
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
68 vert where to start?
  • 67 blueberry
  • Jul 2, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
0
Views
149
1965 - 1973 Classic Mustangs -General/Talk- Jul 2, 2026
67 blueberry
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?