• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

rocker arm shims

  • Thread starter Thread starter loudexhaust
  • Start date Start date May 20, 2008
L

loudexhaust

New Member
May 13, 2006
99
0
0
May 20, 2008
#1
  • May 20, 2008
  • #1
I'm slapping on a pair of unmilled gt40p's and i'm hoping the stock pushrods will work. I was going to order some shims just in case but i could only find them in .030 or .060 thickness. These seem like they may be a little too big so would I have to order new pushrods if my geometry is off by just a little bit?
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
May 20, 2008
#2
  • May 20, 2008
  • #2
I have stock stamped bolt down rockers on my 82. It has iron GT40 heads, not the p's, and a 1986 vintage Rhodes Lifters cam. I have the same setup on the 79 with Comp Cams roller tip rockers and their retrofit studs.

I bought the Crane shim kit that has 3 sizes of shims that you can use individually or in combinations. When I put the GT40 heads on, I experimented with the shims, and finally removed them.

It's run fine with the stock 79 length pushrods for 5 years, and will spin to 6000 rpm as needed. This is with a flat tappet hydraulic setup.

I may be lucky, but I would mock up the stock stuff first and check it. It should work.
 
You must log in or register to reply here.

Similar threads

Resolved Fixing a GT40P Valvetrain nightmare
  • foxbodyclark
  • May 21, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
1K
Fox 5.0 Mustang Tech May 24, 2025
limp
D
AOD TV cable replacement bushing - loose pin?
  • DuluthFoxbody
  • Oct 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
142
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 2, 2026
DuluthFoxbody
D
G
Engine Pushrod Length Question
  • germain101
  • Sep 22, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
744
Fox 5.0 Mustang Tech Sep 25, 2025
Noobz347
J
MEED HELP!! 86 mustang
  • Jacob0121
  • Jan 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
485
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 25, 2026
CAMTWO1070
Surging/stalling! problem or tune?
  • djj62478
  • Oct 4, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
396
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 14, 2026
KRUISR
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?