• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

ROLLER OR NON ROLLER?

  • Thread starter Thread starter SMOKEDYA
  • Start date Start date May 26, 2008

SMOKEDYA

20+ Year Stangneter
Jul 13, 2003
3,637
8
79
Tucson AZ
May 26, 2008
#1
  • May 26, 2008
  • #1
Whats better about building a roller motor versus a non roller motor? peace




john
 

Mustang78

New Member
Feb 8, 2006
486
0
0
Aberdeen, WA
May 26, 2008
#2
  • May 26, 2008
  • #2
roller allows you to run a steeper/bigger cam profile, the roller can roll up a steeper incline and drop off quicker than a flat tappet, if you tried to do some of the things with a flat tappet than you do with a roller you'd wipe out the cam.. remember the flat tappet is 2 flat surfaces sliding on each other and the roller is rolling over the hills, eliminating cam wear and freeing up HP due to less friction.. IMO it's not worth it to convert for a street/strip car, but if you can find a roller block for the same price as a flat tappet go for the roller. Cams and lifters are also much more expensive for the roller, but the lifters can be reused on any cam, it's not matched to that lobe like a flat tappet
 

SMOKEDYA

20+ Year Stangneter
Jul 13, 2003
3,637
8
79
Tucson AZ
May 26, 2008
#3
  • May 26, 2008
  • #3
i thought it went something like that? and another thing i'm looking and weighting out my costs of staying EFI or going carbed! peace


john
 

Gearbanger 101

Straight Outta Locash
20+ Year Stangneter
Aug 10, 2002
9,457
1,377
234
Ontario, Canada
May 26, 2008
#4
  • May 26, 2008
  • #4
Just adding to the first posters answer....the roller valve train is where it's at. Cuts way down on the friction allowing the engine to rev up much more smoothly and freely than a non roller cam would. The roller cam will also outlast the rest of the engine, where a non roller engine will experience considerably more wear on its lifter faces and cam lobes throughout its lifetime.

As far as EFI vs. Carb goes. At this point (or at any point IMO) you're better off sticking with the EFI set up. You'll make as much, if not more power with it along with better off idle torque and drivability, as well as increased fuel economy and cleaner emissions levels. If you were starting from scratch with a stripped bare chassis, then going with a carbureted set up might be more financially viable to you, but at this point It would be more expensive for you to work backwards removing the EFI equipment and prepping your vehicle for a carb swap, than it would to forge ahead with the EFI parts.
 

SMOKEDYA

20+ Year Stangneter
Jul 13, 2003
3,637
8
79
Tucson AZ
May 26, 2008
#5
  • May 26, 2008
  • #5
Gearbanger 101 said:
Just adding to the first posters answer....the roller valve train is where it's at. Cuts way down on the friction allowing the engine to rev up much more smoothly and freely than a non roller cam would. The roller cam will also outlast the rest of the engine, where a non roller engine will experience considerably more wear on its lifter faces and cam lobes throughout its lifetime.

As far as EFI vs. Carb goes. At this point (or at any point IMO) you're better off sticking with the EFI set up. You'll make as much, if not more power with it along with better off idle torque and drivability, as well as increased fuel economy and cleaner emissions levels. If you were starting from scratch with a stripped bare chassis, then going with a carbureted set up might be more financially viable to you, but at this point It would be more expensive for you to work backwards removing the EFI equipment and prepping your vehicle for a carb swap, than it would to forge ahead with the EFI parts.
Click to expand...

as far as EFI or carbed goes i figured that. I'm looking at as much if not more to switch to carb. Emisions isnt a concern. I figure i could have about &1200 alone to go to carbed, to where i'd have $400-650 to stay EFI. I come up with these prices cause all i really need is intake and flywheel and balancer.Maybe a touch more for EFI? The intake is probably gonna be $675 shipped unless i can get a trick flow R for cheap or pick up another brand cheap? I wont use BBK or professional products or the typhon crap. peace



john
 

enyawix

Member
Dec 18, 2005
507
0
19
127.0.0.1
May 27, 2008
#6
  • May 27, 2008
  • #6
SMOKEDYA said:
i thought it went something like that? and another thing i'm looking and weighting out my costs of staying EFI or going carbed! peace


john
Click to expand...

stay EFI using the blue injectors with a stock mass air will let you run E85 or pure alcohol with an adjustable fuel pressure regulator. alcohol give you many tuning options.
 

SMOKEDYA

20+ Year Stangneter
Jul 13, 2003
3,637
8
79
Tucson AZ
May 27, 2008
#7
  • May 27, 2008
  • #7
enyawix said:
stay EFI using the blue injectors with a stock mass air will let you run E85 or pure alcohol with an adjustable fuel pressure regulator. alcohol give you many tuning options.
Click to expand...

we dont have E85 here the lowest oct is 87 and the highest is92. Blue top's? those are 24's so how will the stock mass air work with them? peace



john
 

enyawix

Member
Dec 18, 2005
507
0
19
127.0.0.1
May 27, 2008
#8
  • May 27, 2008
  • #8
Blue top injectors are the 24s stock mass air and 24s will make the system run rich. ethanol needs a richer mix than gas. at 98c / gallon you may want to make your own?
 

Gearbanger 101

Straight Outta Locash
20+ Year Stangneter
Aug 10, 2002
9,457
1,377
234
Ontario, Canada
May 27, 2008
#9
  • May 27, 2008
  • #9
enyawix said:
Light blue top injectors are the 24s....dark blue top injectors are 36's.
Click to expand...
Fix't
 

enyawix

Member
Dec 18, 2005
507
0
19
127.0.0.1
May 27, 2008
#10
  • May 27, 2008
  • #10
Gearbanger 101 said:
Fix't
Click to expand...

true the 1993 cobra blue injectors are 24s
 

SMOKEDYA

20+ Year Stangneter
Jul 13, 2003
3,637
8
79
Tucson AZ
May 27, 2008
#11
  • May 27, 2008
  • #11
enyawix said:
Blue top injectors are the 24s stock mass air and 24s will make the system run rich. ethanol needs a richer mix than gas. at 98c / gallon you may want to make your own?
Click to expand...

dam how is that done?! peace




john
 
You must log in or register to reply here.

Similar threads

K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
485
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
D
Early ford 302 heads
  • Dagasser
  • May 4, 2026
  • The Welcome Wagon
Replies
1
Views
126
The Welcome Wagon May 4, 2026
Noobz347
D
Engine HO cam in non HO roller block ‘93 f150
  • DanC1993f150
  • Mar 21, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
522
Fox 5.0 Mustang Tech Mar 29, 2026
General karthief
M
  • Poll Poll
Stroking a Mexico 289 or newer roller 302
  • MaryJaneTheMustang
  • Aug 12, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
1
Views
161
1965 - 1973 Classic Mustangs -General/Talk- Aug 12, 2026
Bullitt347
Hinge Roller repair kit
  • Rdub6
  • Aug 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
175
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 5, 2026
gkomo
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?