• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Roush 200 Head.

  • Thread starter Thread starter Dohner90
  • Start date Start date Jun 23, 2017

Dohner90

Member
Jul 23, 2014
34
1
8
Jun 23, 2017
#1
  • Jun 23, 2017
  • #1
Ok guys I have been all over looking but cant not find a definitive answer. I will check when I pull motor out and apart but can I run the Roush 200 heads with a B303 cam and 1.7 roller rockers with STOCK 90 bottom end?
 

Black1987

my wife Bedazzled my input shaft
15 Year Member
Jan 9, 2011
1,064
595
174
NC
Jun 23, 2017
#2
  • Jun 23, 2017
  • #2
Dohner90 said:
Ok guys I have been all over looking but cant not find a definitive answer. I will check when I pull motor out and apart but can I run the Roush 200 heads with a B303 cam and 1.7 roller rockers with STOCK 90 bottom end?
Click to expand...
My initial response is it should.

However, every engine is different and without knowing if the cam was degree'd /or installed straight up, if the block has been milled/decked, and or the surface if the heads and the type of gasket you're running.

I would say always check the PVC with some clay or dollar tree playdo

Btw are the heads 2.02 valves and is the stock bottom end 87-92 forged pistons, 86 flat tops, or the 93 up hypers?
 

Dohner90

Member
Jul 23, 2014
34
1
8
Jun 23, 2017
#3
  • Jun 23, 2017
  • #3
I will install the cam straight up, no idea on how to degree or anything like that. The heads were milled down to make them flat. As far as I know the block is stock and not been milled. I get the concept of the playdo but how to I them measure the thickness of the playdo?
 

Black1987

my wife Bedazzled my input shaft
15 Year Member
Jan 9, 2011
1,064
595
174
NC
Jun 23, 2017
#4
  • Jun 23, 2017
  • #4
View: https://m.youtube.com/watch?v=Y66lvdHbm60


You put playdo in the cylinder. You bolt the head on partially with vavletrain on a cylinder. Rotate carefully a full rotation ensuring to stop with you feel any binding. Remove cylinder head, half the playdo carefully and measure with a set of harbour freight calipers.
 

RangerJoe

I leave the horn on while driving
15 Year Member
Apr 26, 2010
2,560
1,146
184
Georgia
Jun 23, 2017
#5
  • Jun 23, 2017
  • #5
Most online valve heads with 2.02 valves or larger will not clear stock piston notches. If you decide to give it a try, make sure you mock it up like others stated.

Joe
 
You must log in or register to reply here.

Similar threads

D
N/A build on fresh stock 302
  • djcarrot
  • Oct 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
457
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 19, 2026
AeroCoupe
K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
519
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
N
Looking for ECU/CHIP for 1992 5.0
  • Nathan26
  • Sep 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
9
Views
344
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 8, 2026
Qtrhrse23
B
SN95 New Heads
  • Blakeknight
  • May 30, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 30, 2025
Noobz347
J
MEED HELP!! 86 mustang
  • Jacob0121
  • Jan 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
492
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 25, 2026
CAMTWO1070
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?