• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Running on 2 cylinders ??

  • Thread starter Thread starter dave's red89lx
  • Start date Start date Jul 30, 2006
D

dave's red89lx

New Member
Mar 30, 2006
8
0
0
Jul 30, 2006
#1
  • Jul 30, 2006
  • #1
Fresh rebuild, TFS street kit, 24 # injectors Installed the cam @ 12 and 6, new autolite plugs (3924), new cap,rotor,wires and coil. tried to fire it up, sounds like a tractor and will not stay running. I then checked and have spark at all cylinders. Pulled the plugs, and they are soaked with fuel. I then started feeling around the headers, & number 3 and 5 are hot but the others are cold. Does anyone have any Ideas on what to check next? I am at my wits end.

Any help would be great.

Dave...
 

Mr. Rustypwnz

Advanced Member
Jun 1, 2005
1,761
63
69
indianapolis/ valdosta ga
Jul 30, 2006
#2
  • Jul 30, 2006
  • #2
How much fuel psi are you running?

Josh
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 30, 2006
#3
  • Jul 30, 2006
  • #3
Cylinder balance test:
Warm the car's engine up to normal operating temperature. Use a jumper wire or paper clip to put the computer into test mode. Start the engine and let it go through the normal diagnostic tests, then quickly press the throttle to the floor. The engine RPM should exceed 2500 RPM's for a brief second. The engine RPM's will increase to about 1450-1600 RPM and hold steady. The engine will shut off power to each injector, one at a time. When it has sequenced through all 8 injectors, it will flash 9 for everything OK, or the number of the failing cylinder such as 2 for cylinder #2. Quickly pressing the throttle again up to 2500 RPM’s will cause the test to re-run with smaller qualifying figures. Do it a third time, and if the same cylinder shows up, the cylinder is weak and isn’t putting out power like it should. See the Chilton’s Shop manual for the complete test procedure

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/
OR
See http://www.dalidesign.com/hbook/eectest.html for more descriptive help
OR
See http://www.mustangworks.com/articles/electronics/eec-iv_codes.html

For those who are intimidated by all the wires & connections, see http://www.actron.com/product_detail.php?pid=16153 for what a typical hand scanner looks like. Normal retail price is about $30 or so at Walmart.

Or for a nicer scanner see http://www.midwayautosupply.com/detailedproductdescription.asp?3829 – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $33.

Do a compression test on all the cylinders.
Take special note of any cylinder that shows up as weak in the cylinder balance test. Low compression on one of these cylinders rules out the injectors as being the most likely cause of the problem. Look at cylinders that fail the cylinder balance test but have good compression. These cylinders either have a bad injector, bad spark plug or spark plug wire. Move the wire and then the spark plug to another cylinder and run the cylinder balance test again. If it follows the moved wire or spark plug, you have found the problem. If the same cylinder fails the test again, the injector is bad. If different cylinders fail the cylinder balance test, you have ignition problems or wiring problems in the 10 pin black & white electrical connectors located by the EGR.

How to do a compression test:
Only use a compression tester with a screw in adapter for the spark plug hole. The other type leaks too much to get an accurate reading. Your local auto parts store may have a compression tester to rent. If you do mechanic work on your own car on a regular basis, it would be a good tool to add to your collection.

With the engine warmed up, remove all spark plugs and prop the throttle wide open, crank the engine until it the gage reading stops increasing. On a cold engine, it will be hard to tell what's good & what's not. Some of the recent posts have numbers ranging from 140-170 psi. If the compression is low, squirt some oil in the cylinder and do it again – if it comes up, the rings are worn. There should be no more than 10% difference between cylinders. Use a blow down leak test (puts compressed air inside cylinders) on cylinders that have more than 10% difference.
 
D

dave's red89lx

New Member
Mar 30, 2006
8
0
0
Jul 30, 2006
#4
  • Jul 30, 2006
  • #4
Stock fuel pressure.
 
D

dave's red89lx

New Member
Mar 30, 2006
8
0
0
Jul 30, 2006
#5
  • Jul 30, 2006
  • #5
Thanks jrichker, but I don't think I am at the point where I can let the engine warm up for the self test. I will try a compression test and post back the findings.
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 30, 2006
#6
  • Jul 30, 2006
  • #6
the timing between the crank and cam are not correct and/or distributor was replaced incorrectly and/or wires are installed incorrectly.. has to be one of the above...
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 30, 2006
#7
  • Jul 30, 2006
  • #7
the timing marks for the crank and cam gears meet each other at 12 and 6 o'clock respectively (also called "dot-to-dot") and the piston in the No. 1 cylinder at top dead center on the compression stroke (both valves closed) are you sure this step was performed correctly...
you can also have only 2 cylinders fireing if wires are put on backwards being clockwise firing order yours should be counter clock wise as in pic. below but with the wireing backwards 1 and 6 would fire......
 

Attachments

  • 7-25-06stangmotorbay001.webp
    37.6 KB · Views: 163
D

dave's red89lx

New Member
Mar 30, 2006
8
0
0
Jul 30, 2006
#8
  • Jul 30, 2006
  • #8
Thanks Bill. Could the distributor being off by one tooth cause this?
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jul 30, 2006
#9
  • Jul 30, 2006
  • #9
no..it would have to be off alot more than that...
 

ls1beater4eva

New Member
May 13, 2005
334
0
0
mooresville
Jul 30, 2006
#10
  • Jul 30, 2006
  • #10
are these stud mounted rockers?
 
D

dave's red89lx

New Member
Mar 30, 2006
8
0
0
Aug 2, 2006
#11
  • Aug 2, 2006
  • #11
Found the problem

Thanks for all of the info guys, The problem was that I had adjusted the rockers incorrectly. Now I just need to read through the Surging idle checklist.

Thanks again.


Dave...
 
You must log in or register to reply here.

Similar threads

K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
408
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
C
Engine Cylinder 5,,7, & 8 run significantly cooler than the other cylinders
  • Crisfixes
  • Sep 27, 2025
  • Fox 5.0 Mustang Tech
Replies
1
Views
318
Fox 5.0 Mustang Tech Sep 27, 2025
Noobz347
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
602
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
Engine 1988 Ford Mustang throwing 2 OBD-1 codes (32 and 63) rough cold start and initial idle
  • mikeah
  • Monday at 12:38 PM
  • Fox 5.0 Mustang Tech
Replies
6
Views
180
Fox 5.0 Mustang Tech Tuesday at 7:31 PM
mikeah
C
For Sale Mint 1993 Calypso 5.0 Convertible
  • Chrispy62
  • Aug 22, 2026
  • Fox Body Mustangs For Sale (1979-93)
Replies
2
Views
244
Fox Body Mustangs For Sale (1979-93) Aug 22, 2026
Chrispy62
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?