• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Running Rich?

  • Thread starter Thread starter jrp27540
  • Start date Start date Sep 14, 2016
  • 1
  • 2
  • 3
Next
1 of 3 Next Last
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Sep 14, 2016
#1
  • Sep 14, 2016
  • #1
I bought an 88 LX 5.0 a few weeks ago. I had a feeling the car was running rich due to the smell from the exhaust. I changed the oil in it last night and the oil smelled of gas. The mods that I have been able to identify at this point are as follows:
  • MAF conversion
  • Cold air intake
  • Bigger upper and lower intake
  • Bigger fuel injectors
  • Bigger fuel pump
  • MSD ignition
  • e303 cam
  • headers
I am used to the 4.6 mustang, but am very very new to the 5.0 fox body. I have been doing some research on this and sounds like it could be a number of things based on the mods done to the car today. I do not see a "check engine" light on, so im not sure if that means the car isnt throwing any codes or not.

At this point, I am looking for any direction that I should start looking at first and work my way down the list. It sounds like I have a large learning curve in front of me with a car that is far from stock... Any nudge in the right direction would be appreciated. I dont want to drive the car until I get this figured out...as im concerned about how much damage has been done to the internals from the previous owner.

Thanks for any information!
 

LiquidStangs

Well-Known Member
Dec 13, 2015
183
216
63
Indianapolis metro area
Sep 15, 2016
#2
  • Sep 15, 2016
  • #2
These cars can have codes even without a check engine light. First step, I'd say, is to pull codes. There's a sticky thread with instructions.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,375
18,122
224
Massachusetts
Sep 15, 2016
#3
  • Sep 15, 2016
  • #3
Technically 1988 Mustangs don't have the check engine light at all, unless it's a Cali Mass air car.

So, step #1 is run the engine codes
 

mikestang63

SN Certified Technician
Aug 27, 2012
11,606
8,859
214
In the garage
Sep 15, 2016
#4
  • Sep 15, 2016
  • #4
jrp27540 said:
I bought an 88 LX 5.0 a few weeks ago. I had a feeling the car was running rich due to the smell from the exhaust. I changed the oil in it last night and the oil smelled of gas. The mods that I have been able to identify at this point are as follows:
  • MAF conversion
  • Cold air intake
  • Bigger upper and lower intake
  • Bigger fuel injectors
  • Bigger fuel pump
  • MSD ignition
  • e303 cam
  • headers
I am used to the 4.6 mustang, but am very very new to the 5.0 fox body. I have been doing some research on this and sounds like it could be a number of things based on the mods done to the car today. I do not see a "check engine" light on, so im not sure if that means the car isnt throwing any codes or not.

At this point, I am looking for any direction that I should start looking at first and work my way down the list. It sounds like I have a large learning curve in front of me with a car that is far from stock... Any nudge in the right direction would be appreciated. I dont want to drive the car until I get this figured out...as im concerned about how much damage has been done to the internals from the previous owner.

Thanks for any information!
Click to expand...

can you define what a "bigger intake and injectors" is.? Is the MAF an aftermarket matched to the injectors or a stock Ford unit. Gas in the oil is either because your injectors are too large, an injector is stuck open, a bad FP regulator or incorrect FP setting, or improper tune. Was the car sitting for a long time or was it cranking a lot with a no start situation? You want tp avoid washing out your motor with fuel or you will end up ruining an engine quick.
 
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 8, 2016
#5
  • Oct 8, 2016
  • #5
OK, I am finally at the point where I can get the codes. Took a while...

So I bought the "Ford Code Reader" that was mentioned in the thread for extracting the codes. I followed the instructions, but I am having issues getting codes to show up on the reader. I know the reader is successfully connecting to the computer because diagnostics take place when I hit the "Test/Hold" button("I hear solenoids moving and engine revs up, fuel pump kicks on, etc"). However it all stops and no codes are read on the device. It just says 000 and the little arrow is still on showing that its communicating to the car. Any ideas around what I might be doing wrong? I also made sure to push in on the clutch after I hit the "Test/Hold" button.
 

Moosee1955

Active Member
Sep 30, 2016
267
55
38
Oct 8, 2016
#6
  • Oct 8, 2016
  • #6
Is the key on position for running your dtc codes test. If your scanner uses a battery, try a fresh one. As far as running rich, yes it could be a malfunction in the fuel regulator. Do a fuel pressure test, check against specs for your car. Also see if any fuel in hose that connects to regulator. If you see fuel out of hose replace reg. as far as too big of injectors, everything I've read says extra fuel if too large should return to tank. You can hear if each injector is functioning with a stethoscope. A shop or friend can maybe do further diagnosis of injectors. to me if you have a stuck injector, that spark plug would be wet with fuel. Pull your plugs/ check. My 2 cents, Moose.


Sent from my iPhone using Tapatalk
 
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 8, 2016
#7
  • Oct 8, 2016
  • #7
Yes,the key is in the on position. I just opened the scanner today and put new batteries in it.

The fuel regulator has a pressure gauge on it. See the pic below; its showing almost 50 psi at idle.

Ill pull the black hose and see if there is any fuel in it. Ill also pull the plugs and inspect.

Just to provide some more info around the car. The previous owner replace the original upper and lower intake with an upper and lower off of a Ford Explorer(pics blow). Apparently the intake was bigger on the Explorer.

The car also has a MAS installed. I cant tell if its stock or added. Again the past owner told me it was stock...but from all that I have read only Cal cars had MAF in 88. When I had the dash out replacing the heater core, I looked over the ECU to see if I could see any wire splices that could have led to a MAF conversion. I noticed two (see pic below); appeared to be a red and black wire. Not sure what that is, but someone has added something. The previous owner did install a bigger MAF with the upper/lower intake.

To recap on the other items already listed:
  • MAF conversion (possibly??? Cant tell if its stock or not)
  • EGR elimnator plug
  • Cold air intake
  • Bigger upper and lower intake (From Ford Explorer)
  • Bigger fuel injectors
  • Bigger fuel pump
  • MSD ignition
  • e303 cam
  • headers
 

90sickfox

Wasn't a pretty sight...and I've got big hands
SN Certified Technician
Mar 2, 2015
6,953
5,831
213
Oct 8, 2016
#8
  • Oct 8, 2016
  • #8
That car needs a tune....The filter needs to go into the the fender well to get away from the fan. Fuel pressure should be set at about 43lbs without the vac line connected.

If you can shoot an email to Willy Lynch at dirtydirtyracing.com he could get you a chip made. He uses Moates Quarter Horse. He's one of the best tuners around and sells QH through their store.

You've got to find out the size of the injectors....color...or part number on injectors.

If you have bigger injectors and a stock MAF without a tuned chip then that's probably why its running rich.
 
Reactions: RaggedGT
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 8, 2016
#9
  • Oct 8, 2016
  • #9
90sickfox said:
That car needs a tune....The filter needs to go into the the fender well to get away from the fan. Fuel pressure should be set at about 43lbs without the vac line connected.

If you can shoot an email to Willy Lynch at dirtydirtyracing.com he could get you a chip made. He uses Moates Quarter Horse. He's one of the best tuners around and sells QH through their store.

You've got to find out the size of the injectors....color...or part number on injectors.

If you have bigger injectors and a stock MAF without a tuned chip then that's probably why its running rich.
Click to expand...

Thanks for the information ! Ill defiantly contact him as I had a feeling a tune was needed with all the changes the previous owner added.

As for your comment around removing the vac line connected to the fuel regulator. Are you saying that I need to remove it all together, or remove it and adjust the fuel pressure then reinstall the vac line? I just want to make sure as I thought the vac line was a must in order for it to control the fuel pressure.

Ill find out the size of the injectors. I know the MAF isnt stock as it was replaced to account for the mods. Im not sure the size of the MAS though; I should figure that out as well.
 

RaggedGT

Been here over a DECADE and still no CT
Mod Dude
Jul 20, 2014
4,766
3,224
203
Taylorsville ky
Oct 8, 2016
#10
  • Oct 8, 2016
  • #10
@90sickfox gives pretty good advice, that's why I listen to that dude lol
But yeah, 'Un plug' the vacuum line from the fpr,set your pressure,plug it back in
 
Reactions: 90sickfox

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,133
10,752
213
polk county florida
Oct 9, 2016
#11
  • Oct 9, 2016
  • #11
I'd be suspicious of that computer have'n the back open like that. Its a remanufactured I think. Also throttle body and maf looks stock tto me but really can't tell from pics, likely from the explorer that the intake is from, not a bad thing. Need fan shroud and puke tank. At this point I don't think a tune will do any good till you identify some of the claimed mods, but I am not a expert, pervious owner's don't always tell the whole truth and nothin but the truth, does it have a lopy idle?
 

Moosee1955

Active Member
Sep 30, 2016
267
55
38
Oct 9, 2016
#12
  • Oct 9, 2016
  • #12
It's always fun trying to get fuel mixtures on pumped motors right. In the old days we'd change jets and needles in carbs. These days with computers and injection, it's not easy. In theory the computer is supposed to richer or lean where necessary, but it don't work that way. Factor in all the hacking that the last guy or two did, and you've got a recipe for trouble on your hands. Correct any weird wiring or splice ins first. Make sure you have right computer. Full ignition tune up, if you haven't already. Try to stay away from made in China parts. Use Ford stuff whenever possible, and get it fuel tuned by an expert. Keep us posted with results. With high performance engines, you might not get it perfect, but you'll get better.


Sent from my iPhone using Tapatalk
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,133
10,752
213
polk county florida
Oct 9, 2016
#13
  • Oct 9, 2016
  • #13
Yea, what moose said. I can't even tune a carb anymore but I can tune a fish.
 

Moosee1955

Active Member
Sep 30, 2016
267
55
38
Oct 9, 2016
#14
  • Oct 9, 2016
  • #14
You know what they say. The worst day fishing, is better than the best day working!


Sent from my iPhone using Tapatalk
 

mikestang63

SN Certified Technician
Aug 27, 2012
11,606
8,859
214
In the garage
Oct 9, 2016
#15
  • Oct 9, 2016
  • #15
Holy mother of hack jobs. I'd see if you can get an entire harness from teh same year from MPS or otherJY and start fresh.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 9, 2016
#16
  • Oct 9, 2016
  • #16
The first step is to dump the codes with ignition on, engine not running. Do that first and then after it has successfully dumped the codes, start the engine with the code reader connected. Do not turn the ignition off between dumping the codes with the engine off and the engine off.
 
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 9, 2016
#17
  • Oct 9, 2016
  • #17
jrichker said:
The first step is to dump the codes with ignition on, engine not running. Do that first and then after it has successfully dumped the codes, start the engine with the code reader connected. Do not turn the ignition off between dumping the codes with the engine off and the engine off.
Click to expand...

I tried again tonight and I just cant get the ford code reader to give me any codes...the reader just sticks on 000. I hit the start test with key forward and I hear the fuel pump engage and here a click or two under the hood then it stops and no codes are displayed. It just sticks on 000. Same results with the engine on. I start the test on the reader, the engine revs up then goes back to idle...then noting....just 000. The dash doesn't have a light bulb where the check engine light is, so im going to get a test light and see if I can get codes to dump using that method.
 
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 9, 2016
#18
  • Oct 9, 2016
  • #18
OK, I got a few hard numbers. The throttle body is 70mm(printed on throttle body). The MAF didnt have a number on it, but it was 2 7/8 inches in diameter which is around 73mm. The fuel injectors have a gray top; i think they are 19lbs injectors based on my google searches. Im going to keep trying to get the codes off of the Eec; its been a royal pain. I cant get codes on the ford code reader, so im going to try the test light method. Thanks everyone for your help; its greatly appreciated!

 

RaggedGT

Been here over a DECADE and still no CT
Mod Dude
Jul 20, 2014
4,766
3,224
203
Taylorsville ky
Oct 9, 2016
#19
  • Oct 9, 2016
  • #19
Is the car a Stick? Or Auto?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,375
18,122
224
Massachusetts
Oct 9, 2016
#20
  • Oct 9, 2016
  • #20
For one, the breather needs to come off the valve cover, and the vac hose to the TB connected, or at least cap the one on the VC


Sent from my iPhone using Tapatalk
 
  • 1
  • 2
  • 3
Next
1 of 3 Next Last
You must log in or register to reply here.

Similar threads

S
Fox '87 GT can't get to stay running
  • spilly
  • Mar 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
27
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 20, 2026
spilly
S
J
i need help
  • JK.
  • Oct 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
22
Views
639
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 28, 2026
JD1964
R
Efi to car pcv HELP !
  • rgrendell
  • Jul 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
23
Views
732
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 2, 2026
Noobz347
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
320
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
D
Loud noise(s) from Engine Bay
  • DuluthFoxbody
  • Oct 25, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
14
Views
387
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 5, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?