• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Running the summit battery relocation kit

  • Thread starter Thread starter Busted07
  • Start date Start date Feb 7, 2006

Busted07

I need my gorilla to be about an inch longer.
Nov 15, 2005
0
3
0
Feb 7, 2006
#1
  • Feb 7, 2006
  • #1
I will have the stock alternator (converted from efi to carb) and am hoping that it will run everything fine, but my question is, i bought the summit relocation kit, a switch and stuff, but a friend of mine says that i need alot bigger cable than the kit that summit sells to move my battery. is there any truth to that? i wont have high powered audio, or anything besides the lights, gauges and stuff.
 

mbsprinks281

Member
Apr 19, 2005
58
2
9
Lockport, IL
Feb 7, 2006
#2
  • Feb 7, 2006
  • #2
Two things. The summit battery kit will not get you through tech at the track. Also, I used 1 gauge welding cable, its cheaper than battery cable and alot more flexible. I would give some serious thought about running a fused line to the alternator. Look here. http://buffhomer.corral.net/custom.html
 
L

luckythirteen13

New Member
Jul 19, 2005
648
0
0
Anaheim, CA
Feb 7, 2006
#3
  • Feb 7, 2006
  • #3
the summit relocation kit has wires that are way to small. you need 2 gauge minimum. going to a welding supply place and its pretty cheap. also, if you plan to take the car to the track, the summit relocation kit wont pass if you have a hatch back
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 7, 2006
#4
  • Feb 7, 2006
  • #4
Rear mounted battery ground wiring. Follow this plan and you will have zero ground problems.

One 1 gauge or 1/0 gauge wire from battery negative post to a clean shiny spot on the chassis near the battery. Use a 5/16” bolt and bolt it down to make the rear ground. Use a 1 gauge or 1/0 gauge wire from the rear ground bolt to a clean shiny spot on the block.

One 4 gauge wire from the block where you connected the battery ground wire to the chassis ground where the battery was mounted up front. Use a 5/16” bolt and bolt down the 4 gauge engine to chassis ground, make sure that it the metal around the bolt is clean & shiny. This is the alternator power ground.

Crimp or even better, solder the lugs on the all the wire. The local auto stereo shop will have them if the auto parts store doesn't. Use some heat shrink tubing to cover the lugs and make things look nice.

The computer has a dedicated power ground wire with a cylindrical quick connect (about 2 ½”long by 1” diameter. It comes out of the wiring harness near the ignition coil & starter solenoid (or relay). Be sure to bolt it to the chassis ground in the same place as you bolted the alternator power ground. This is an absolute don’t overlook it item for EFI cars
 

Busted07

I need my gorilla to be about an inch longer.
Nov 15, 2005
0
3
0
Feb 8, 2006
#5
  • Feb 8, 2006
  • #5
Well, ya know, thats pretty frustraing that summit doesnt say anything about it not being track legal. ill see what i can do about getting the welding cable, and following your advice, thanks again!
 

Busted07

I need my gorilla to be about an inch longer.
Nov 15, 2005
0
3
0
Feb 8, 2006
#6
  • Feb 8, 2006
  • #6
Also, can i use the same welding cable for the positive wire to the soilenoid and starter or will that be overkill. i figure it would be cheaper if i bought it in one giant chunk.
 
L

luckythirteen13

New Member
Jul 19, 2005
648
0
0
Anaheim, CA
Feb 8, 2006
#7
  • Feb 8, 2006
  • #7
use the same 2gauge or larger cable for EVERYTHING. the wire from the battery to the ground, the wire from the battery to the starter, the kill switch and even the wire coming from the alt to the battery
 

Busted07

I need my gorilla to be about an inch longer.
Nov 15, 2005
0
3
0
Feb 8, 2006
#8
  • Feb 8, 2006
  • #8
Awesome, i appreciate the info!
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 8, 2006
#9
  • Feb 8, 2006
  • #9
For a battery cut off switch, see http://www.moroso.com/catalog/categorydisplay.asp?catcode=42225
is the switch http://www.moroso.com/catalog/images/74102_inst.pdf is the installation instructions.
Use the super duty switch and the following tech note to wire it and you will
be good to go.

Use the Moroso plan for the alternator wiring and you risk a fire. The 10
gauge wire they recommend is even less adequate that the stock Mustang
wiring.

There is a solution, but it will require about 40' of 18 gauge green wire.

Wire the battery to the two 1/4" posts as shown in the diagram.

The alternator requires a different approach. On the small alternator plug
there is a green wire. It is the sense lead that turns the regulator on when
the ignition switch is in the run position. Cut the green wire and solder the 40'
of green wire between the two pieces. Use some heat shrink to cover the
splices. See http://fordfuelinjection.com/?p=7 for some excellent
help on soldering & using heat shrink tubing.

Run the green wire back to the Moroso switch and cut off the excess wire.
Try to run the green wire inside the car and protect it from getting cut or
chaffed. Crimp a 18 gauge ring terminal (red is 18 gauge color code for the crimp
on terminals) on each wire. Bolt one ring terminal to each of the 3/16" studs.
Do not add the jumper between the 1/4" stud and the 3/16" stud as shown it the
Moroso diagram.

How it works:
The green wire is the ignition on sense feed to the regulator. It supplies power
to the regulator when the ignition switch is in the run position. Turn the
Moroso switch to off, and the sense voltage goes away, the voltage
regulator shuts off and the alternator quits making power.

See the following website for some help from Tmoss (diagram designer) &
Stang&2Birds (website host) for help on 88-90 wiring and lots more…

http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

Diagram courtesy of Tmoss and Stang&2birds.
 

Busted07

I need my gorilla to be about an inch longer.
Nov 15, 2005
0
3
0
Feb 8, 2006
#10
  • Feb 8, 2006
  • #10
That is some awesome information, but my application will be different being that i have no fuel injection anymore. I think it will be a much simplier route, but the information is awesome noneteless!
 
You must log in or register to reply here.

Similar threads

F
Alternator Not Charging
  • Fri Guy
  • Aug 29, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
547
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 31, 2025
AeroCoupe
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
486
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
SN95 The Unicorn
  • HANO Motorsports
  • May 18, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
21
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 15, 2025
HANO Motorsports
R
What's it Worth? 1997 Cobra, a ton of mods and restoration
  • riored97snake
  • Jun 18, 2026
  • What is it Worth?!?!?
Replies
2
Views
510
What is it Worth?!?!? Jun 21, 2026
riored97snake
R
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?