Fox Rusted out strut towers

idareu · May 22, 2022

I've been out of the Mustang game for 12 years, which has been too long by about 12 years. I came across an 89 LX 5.0 5spd fastback for $5,500. The story is that it was a father/son project that fell by the wayside and has been sitting for many years. I stopped by for another look and was able to take it for a drive. The car runs strong and shifts well but needs a ton of work (interior, paint, etc...) My concern is the amount of rust on the strut towers as I have no experience welding and don't know how big of a job it will be to have this fixed so I'm reaching out to the StangNet members for any input if this could make or break the car.

Passenger Side

Driver Site

GroverDill · May 22, 2022

5500 for that? Not a chance I would consider that car

check the frame rails and the cowl area too, i would suggest being very careful

Mustang5L5 · May 22, 2022

I’d be hard passing on that. If you need to pay someone to fix those, it’s not going to be cheap.

Spend a couple grand more on a solid car.

evintho · May 22, 2022

It's fixable but then, I've that before. If it's that rotted there......where else is there rust/rot? There's probably a lot you don't see. $5500 is a good price for a Fox body but there's a reason why. I'd save a little more money and look elsewhere.

idareu · May 22, 2022

Thanks to all of you for the input. After I posted this thread, I came back and looked and the pictures and asked myself "If I had a 5.0 in the garage, could I recommend this car to someone?" That answer was a big negative. It's like y'all said, if there is rust there, where else is there rust, and how bad would it be. I was so amped just getting to drive one today that my judgement was a bit clouded.

Mark 7 LSC · May 25, 2022

There's plenty of other Fox body cars out there with the 5.0 motor that can be upgraded just like the Mustang. For example the 1987-1992 Lincoln Mark 7 LSC

BlakeusMaximus · May 25, 2022

I’d pass. I had one like that and sold it to a guy that said he could fix it. I always wonder what happened to that car. Probably my most favorite fox I had.

Mstng93SSP · May 25, 2022

This was one of my favorite cars I had. It was ROTTEN.....door jams, cowl, etc. 93 with a nice black interior. Same deal, sold into a guy who said he was going to fix it. This was 2013. Car has never been registered since then and last I checked is still in my name.

BlakeusMaximus · May 25, 2022

Yeah @Mstng93SSP, floor, hinge pillars, shock towers and probably more were all rusting out. I drove that car for quite a few years. Thought I was going to do the repair on that car but came across my current rust free GT and moved on. That coupe was a 1990 from Michigan, I found out later.

Mustang5L5 · May 25, 2022

I fixed the towers on my car. Only reason I did so was due to the sentimental factor of the car to me. It was a big project that took me pretty much an entire summer to do.

I’d never do it again unless the car was something like a Saleen or 93 Cobra. I would also never buy a car that had repaired frame rails.

Pass side was an easy patch. Drivers side was a bigger job.

Spend the extra money on a clean car.

limp · May 25, 2022

Had some friends throughout the years who could talk to metal.... they could do a project like that in few days and you could hardly tell it was done..
Hate people like that...LOL... Hate musicians too.... God didn't give me any of that talent........

Bullitt347 · May 25, 2022

If you are going to go through the trouble to fix it, get rid of the strut towers and put a Pinto/Mustang II double "A" arm front suspension in it. Without the strut towers a big block fits with ease.

idareu · May 25, 2022

Thanks all for the replies. I did decide to pass on it. I'll let someone else tackle that job. I can do mechanical, interior, etc... but paint/body isn't something I've learned to do. I have a soft spot for Fox body Mustangs. My first at 16 was an 84 GT, later I had a red 89 coupe, and finally in early 2000's I bought a 1993 Cobra that I unfortunately had to sell in 2010 when I was in-between contracting gigs. It killed me to sell it but had to take care of the family first. Now things are better and I'm on the hunt for a project. I just need find the right one. I suspect y'all will see me around here more often.

General karthief · May 25, 2022

So what are you looking for?
I figure a rust free body?

WindsorPenchant · May 26, 2022

Mustang5L5 said:
Pass side was an easy patch. Drivers side was a bigger job.

I think I'll be doing the drivers side sometime soon now I've got mine stored up to tear down.. The intermediate owner had the pass side patched following an MOT failure on rusted passenger strut tower (only 2-3 years ago) but drivers side looks not too pretty from what you can see of it anyway!

I need a new brake booster to fix a vacuum leak and so I'll get a closer look then and see how everything looks once I can get close and personal.
Slightly there is more room to manoeuvre being only the 2.3 but engine's gotta come out if I'll need to get serious about repairing that.

Hoping that it's just limited to the bad areas I can already inspect with all the hardware in place!

idareu · May 26, 2022

General karthief said:
So what are you looking for?
I figure a rust free body?

Good question, So ideally what I'm looking for is this (in order of priority):

* A 1989 - 1993 5spd 5.0 coupe or hatchback (Verts are nice but not sure I'd prefer one over the other 2 body styles).
* I'd like it to have minimal rust, give these cars are 30+ years old, surface rust is expected but I'd shy away from any large holes like I saw this past weekend.
* Ideally it would be in a drive-able condition (running and shifting okay).
* Outside color isn't as important as interior color. I know that may sound weird but I like almost all of the colors except for white/almond (1989 color).
* Now for the interior, I've never been a fan of red interior so Grey or Black would be preferred.
* I expect to have wear and tear inside and have no issues redoing the dash, door-panels, seats, etc...

Price-wise is the harder part, right now I have about $7k to play with. I know that won't get me much in today's market and I'll probably need to get $10k+ in order to get really serious in finding one. While I keep saving, I need to be patient but I'm still looking, Part of the fun of finding a new toy is the hunt, you never know what you can find. I just have to keep my emotions in check while I'm looking. I was so stoked to see one for $5,500 that I wasn't slowing down to think about what I really wanted or what I could be getting into. It's easy to see one for a low price and get amped up but there is a difference between a project and a potential basket-case.

General karthief · May 26, 2022

I have a hatch that has no rust other than surface, mostly complete roller, interior all there but ruff, if interested pm me.

Mstng93SSP · May 26, 2022

Right now near me is this car. I have seen it in person. It is rust free runs/drives etc. Black interior. $7000 asking on FB Marketplace Honolulu. So, I guess my point is they are out there in the 7k range. Be patient is what I ALWAYS advise.

idareu · May 27, 2022

General karthief said:
I have a hatch that has no rust other than surface, mostly complete roller, interior all there but ruff, if interested pm me.

Interesting. I will shoot you a PM for more details. Never hurts to check things out.

idareu · May 27, 2022

Mstng93SSP said:
Right now near me is this car. I have seen it in person. It is rust free runs/drives etc. Black interior. $7000 asking on FB Marketplace Honolulu. So, I guess my point is they are out there in the 7k range. Be patient is what I ALWAYS advise.

That's a nice looking ride. I hadn't thought about FB marketplace. I've been looking at Craigslist, Autotrader, Autotrader classic, Ebay, etc... Thanks for the tip! I also need to lookup some Mustang clubs here in Central Florida and start hitting the meet-ups.

Fox Rusted out strut towers

idareu

GroverDill

GoldMember

Mustang5L5

That is…until I whipped out my Bissell

evintho

idareu

Mark 7 LSC

BlakeusMaximus

Still got to try a little lube on my speedo head

Mstng93SSP

You have a nice rear end there Dave.

BlakeusMaximus

Still got to try a little lube on my speedo head

Mustang5L5

That is…until I whipped out my Bissell

limp

wrap a little cheese around it and its a done

Bullitt347

I have been doing it wrong this whole time

idareu

General karthief

wonder how much it would cost to ship you a pair

WindsorPenchant

Active Member

idareu

General karthief

wonder how much it would cost to ship you a pair

Mstng93SSP

You have a nice rear end there Dave.

idareu

idareu

Similar threads

Fox Rusted out strut towers

GoldMember

That is…until I whipped out my Bissell

Still got to try a little lube on my speedo head

You have a nice rear end there Dave.

Still got to try a little lube on my speedo head

That is…until I whipped out my Bissell

wrap a little cheese around it and its a done

I have been doing it wrong this whole time

wonder how much it would cost to ship you a pair

Active Member

wonder how much it would cost to ship you a pair

You have a nice rear end there Dave.

Similar threads

Privacy & Transparency

Privacy & Transparency