• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Shifter Install

  • Thread starter Thread starter SteedaGT9150
  • Start date Start date Dec 25, 2007

SteedaGT9150

Advanced Member
Nov 10, 2004
1,351
59
68
Maryland
Dec 25, 2007
#1
  • Dec 25, 2007
  • #1
Alright, as the title says im installing my tri-ax tomorrow. how do i get the back square off of the shifter? also are there any tricks or things to watch out for ? thanks
 

Roland69

Sergeant Tangnet
Sep 17, 2005
2,867
3
58
Port Elgin, Ontario
Dec 25, 2007
#2
  • Dec 25, 2007
  • #2
I ended up removing the whole center console. The back bolts holding the lower boot on were a tight reach.
 

ACSPONY

20+ Year Stangneter
Oct 10, 2004
711
2
19
Ohio
Dec 25, 2007
#3
  • Dec 25, 2007
  • #3
Roland69 said:
I ended up removing the whole center console. The back bolts holding the lower boot on were a tight reach.
Click to expand...

x2

Be careful of the clips that hold the shifter boot to the floor. Mine were rusted and most of them just sheared off when I took the old shifter assembly out. Be gentle if you take the console out, it will break easily.
 

91 HATCH

Banned
May 17, 2007
262
0
0
illinois
Dec 25, 2007
#4
  • Dec 25, 2007
  • #4
i run the tri-ax and love it the shifter takes a little getting used to on 2-3 shift instead of moving it over you just hit it straight forward it always go's
 

blackened88lx

Active Member
Aug 9, 2006
0
4
28
Connecticut
Dec 26, 2007
#5
  • Dec 26, 2007
  • #5
Not sure what you mean by the "back square" of the shifter. There's no need to remove the center console, I have pretty big hands and although it was a bitch, I got it done. Proper tools are key.

Pull the shift knob
The plastic boot trim piece just snaps out
Take out the 4 screws for the lower boot. 2 rear, 2 front (bitch!)
Pull the 4 shifter bolts, and remove the shifter.
Clean the sealing surfaces really well, apply a layer of black rtv, and let it tack up for a couple minutes.
Install the new shifter with the 4 bolts, making sure the ball engages with the socket in the tranny.
Install the handle if not done so already.
Set your shift stops! Put the tranny in 3rd gear and turn the stop in until it ALMOST touches the shifter. You want a tiny gap between the stop and shifter. You don't want it to touch the shifter and possibly prevent it from going all the way into gear, but if you push forward on the shifter with a little force, you want it to hit the stop. Do the same in 4th gear, then make sure the stops look good for all gears.
Install your lower boot. The front bolts are going to be even worse this time around. Just face it, your hands will be bleeding, and you will be swearing, but you'll finger it out.
Snap in the upper boot
Screw on your shift knob
 

SteedaGT9150

Advanced Member
Nov 10, 2004
1,351
59
68
Maryland
Dec 26, 2007
#6
  • Dec 26, 2007
  • #6
thanks guys, just started, having some problems with one of the lower bolts for the lower boot, im sure ill keep you updated
 

SteedaGT9150

Advanced Member
Nov 10, 2004
1,351
59
68
Maryland
Dec 26, 2007
#7
  • Dec 26, 2007
  • #7
how do u remove the center console? one of my bottom bolts to my shifter is bent or all ****ed up...this is just turning into a big cluster ****
 

Roland69

Sergeant Tangnet
Sep 17, 2005
2,867
3
58
Port Elgin, Ontario
Dec 26, 2007
#8
  • Dec 26, 2007
  • #8
there are 2 sheet metal screws by the radio frame that I had a hard time finding. They look like they are not a part of the center console but they are. the rest of the console is easy to get out.
 
You must log in or register to reply here.

Similar threads

B
Fuel 1990 installing edelBrock intake
  • Beaker
  • Oct 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
338
Fox 5.0 Mustang Tech Oct 6, 2026
Noobz347
Salvage/rebuilt title question
  • djj62478
  • Oct 2, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
216
1996 - 2004 SN95 Mustang -General/Talk- Oct 2, 2026
DadLife0724
4
Drivetrain Wilwood Clutch and Brake Pedal Combo Installation - Help
  • 427stang
  • Jul 8, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
127
Fox 5.0 Mustang Tech Jul 8, 2026
427stang
4
3
B&m hammer shifter c4 question
  • 387lx
  • Mar 18, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
404
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 19, 2026
387lx
3
Swapping clutch pedal hanger-
  • woodsnake
  • Nov 8, 2026
  • Classic Mustang Specific Tech
Replies
0
Views
55
Classic Mustang Specific Tech Nov 8, 2026
woodsnake
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?