SLP exhaust install. HELP!

DrK MrK iV · Apr 7, 2004

OK, So I get my SLP loudmouth catback exhaust in today.
So I start unbolting the stock exhaust. Now I had to cut the stock exhaust to get it off because of the rear axle... But many of you already knew that. BTW Im not using jackstands, jacks or anything. Just me and the car and a tight ass fit. Now it time to install the aftermarket one. WTF?! Im going to have to go exactly the same way stock was-but I had to cut the stock piping in order to get it off... So how the hell do I install this thing. The pipe can not go under the axle because it sits too low, but I can't get it to go over the axel because of the angles and the pipe hitting the ground. How the hell do I do this? I can't go anywhere because I have no mufflers!

DaDDyGSp0T · Apr 7, 2004

DrK MrK iV said:
OK, So I get my SLP loudmouth catback exhaust in today.
So I start unbolting the stock exhaust. Now I had to cut the stock exhaust to get it off because of the rear axle... But many of you already knew that. BTW Im not using jackstands, jacks or anything. Just me and the car and a tight ass fit. Now it time to install the aftermarket one. WTF?! Im going to have to go exactly the same way stock was-but I had to cut the stock piping in order to get it off... So how the hell do I install this thing. The pipe can not go under the axle because it sits too low, but I can't get it to go over the axel because of the angles and the pipe hitting the ground. How the hell do I do this? I can't go anywhere because I have no mufflers!

here is what u do....get $30 and take it to a muffler shop take them 15 minutes

DrK MrK iV · Apr 7, 2004

DaDDyGSp0T said:
here is what u do....get $30 and take it to a muffler shop take them 15 minutes

And how do I get there? I have no mufflers, because I cut them off.

95kobrah · Apr 7, 2004

how far is it? its not going to hurt the car with no mufflers, just going to be a bit loud... many people drive around with just long tubes.... just take it to the shop, i could not imagine doing any underbody work without even a jack stand or floor jack!

DrK MrK iV · Apr 7, 2004

So theres absolutly no way I can do this without a lift pretty much? How loud is loud? I don't want to piss off people driving to the shop... Which is right next to a mall.

Ryan02Stang · Apr 7, 2004

haha...its not that loud man...trust me! take it to a muffler shop...theyll get that baby in there in under a half hour!

95kobrah · Apr 7, 2004

DrK MrK iV said:
So theres absolutly no way I can do this without a lift pretty much? How loud is loud? I don't want to piss off people driving to the shop... Which is right next to a mall.

well... loud like itll probably sound like an old muscle car with a big block... just dont get on it too much... and as far as id say, due to the gemoetry of the pipes and the height off the ground, id say yes you need quite a bit of room under there to work, i put exhaust on both may cars with them about 1.5 ft. off the ground in my garage with some jackstands, and it was still fairly difficult. The muffler shop has a lift and will probably only take 20 mins to do.

DrK MrK iV · Apr 7, 2004

95kobrah said:
well... loud like itll probably sound like an old muscle car with a big block... just dont get on it too much... and as far as id say, due to the gemoetry of the pipes and the height off the ground, id say yes you need quite a bit of room under there to work, i put exhaust on both may cars with them about 1.5 ft. off the ground in my garage with some jackstands, and it was still fairly difficult. The muffler shop has a lift and will probably only take 20 mins to do.

What will it sound like If I do get on it. Just out of curiousity.

95kobrah · Apr 7, 2004

DrK MrK iV said:
What will it sound like If I do get on it. Just out of curiousity.

Then do what we all would do... drop the hammer and be ready for some eardrum bustin... but dont expect it to run like it had exhaust, with no backpressure and oxygen sensors it may act a lil funny.

DrK MrK iV · Apr 7, 2004

Ok thanks. So pretty much they just got to put the pipes at extreme angles to get them to fit. No welding right?

BlkDragon · Apr 8, 2004

I've got that Cat-Back. You shouldn't have any trouble fitting it over the axle. It comes in pieces w/slip joint and collars. No welding needed..

CottonBurnerz · Apr 8, 2004

I had to hack saw my stock cat-back as well.. then when I put the magnapack on.. the tail pipe that came with it was separated.. so it was an easy install.

BuffaloZone · Apr 8, 2004

Didn't need to cut my factory system out at all - used a hoist, unbolted bottom of right rear shock, both upper control arms, unbolted driveshaft. Old came right out and SLP went right in. (Now replaced with Borla)

No jacks or jackstands...

DrK MrK iV said:
OK, So I get my SLP loudmouth catback exhaust in today.
So I start unbolting the stock exhaust. Now I had to cut the stock exhaust to get it off because of the rear axle... But many of you already knew that. BTW Im not using jackstands, jacks or anything. Just me and the car and a tight ass fit. Now it time to install the aftermarket one. WTF?! Im going to have to go exactly the same way stock was-but I had to cut the stock piping in order to get it off... So how the hell do I install this thing. The pipe can not go under the axle because it sits too low, but I can't get it to go over the axel because of the angles and the pipe hitting the ground. How the hell do I do this? I can't go anywhere because I have no mufflers!

ds02torchgt · Apr 8, 2004

go buy some jack stands and a jack............its defineitly not a waste of money!!!!!

DrK MrK iV · Apr 8, 2004

Yea yea... I know Im cheap as hell. Im going to go buy a good jack and jackstand this weekend. I just started doing mods to my car, so Im slowly buying tools for it. I guess jacks and jackstands should have been number one instead of number 3...

ds02torchgt · Apr 8, 2004

hey no ones perfect. lets see stuff i need, or mods for the mustang? ive gone without grocerys. ya know. also i built some ramps out of 2x8s really helpful.

DrK MrK iV · Apr 8, 2004

Yea yea. So I called the shop, and I told him the situation. He says he might need to drop the axle. I think thats bull****, so I just need to get the car high enough to get it at an angle to put it over the axle right?

MAC[H]Z · Apr 8, 2004

Jack the car with your factory jack and put it on blocks (good blocks) and let the rear axle hang and slide the pipe over the axles and your done....

SilverSteed · Apr 8, 2004

He will NOT have to drop the axle. The SLP stuff is in 3 pieces, and is a very simple install once its on a lift or jack stands. Just take it and don't let him charge you for dropping the axle. It should be no more than an hour's labor.

Andy

DrK MrK iV · Apr 8, 2004

Yea I went to the shop and helped them. It took 15 minutes once it was on a lift. Im deffinatly going to get some jackstands and a jack soon. Thanks for the help. BTW it sounds pretty mean. No loud enough though. An Xpipe should fix that though.

SLP exhaust install. HELP!

DrK MrK iV

New Member

DaDDyGSp0T

DrK MrK iV

New Member

95kobrah

DrK MrK iV

New Member

Ryan02Stang

Active Member

95kobrah

DrK MrK iV

New Member

95kobrah

DrK MrK iV

New Member

BlkDragon

New Member

CottonBurnerz

Banned

BuffaloZone

New Member

ds02torchgt

New Member

DrK MrK iV

New Member

ds02torchgt

New Member

DrK MrK iV

New Member

MAC[H]Z

New Member

SilverSteed

Member

DrK MrK iV

New Member

Similar threads

SLP exhaust install. HELP!

New Member

New Member

New Member

Active Member

New Member

New Member

New Member

Banned

New Member

New Member

New Member

New Member

New Member

New Member

Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency