smog system delete

Custom tune for one.


The engine will run fine. Not like the smog junk robs any HP. It just will run a little dirty and if you delete the EGR, a custom tune is mandatory.

You'll also get check engine codes for the missing components
 
the egr is not part of the smog system. your car will run just fine without a smog pump(as long as you remove your converters, or get an off road crossover pipe). this won't cause a CEL either. deleting the egr stuff is not a good idea unless you get a custom tune.

to delete the smog system, all you have to do is remove the pump and brackets, and tubing, plug the hole in your crossover pipe where the tubing enters, and remove the tubing that runs from the back of your heads into the smog pump. you can plug the holes in the heads with a 5/8 bolt, 11tpi, about 1 inch long, or a broken off spark plug. you will also have to buy a new serp. belt.
 
the egr is not part of the smog system. your car will run just fine without a smog pump(as long as you remove your converters, or get an off road crossover pipe). this won't cause a CEL either. deleting the egr stuff is not a good idea unless you get a custom tune.

to delete the smog system, all you have to do is remove the pump and brackets, and tubing, plug the hole in your crossover pipe where the tubing enters, and remove the tubing that runs from the back of your heads into the smog pump. you can plug the holes in the heads with a 5/8 bolt, 11tpi, about 1 inch long, or a broken off spark plug. you will also have to buy a new serp. belt.

LOL this is exactly what i did! I plan on keeping the EGR! Car has no converters.
 
I wouldn't worry about a tune especially if you do it correct and don't have any CEL pop up on ya. I deleted all my smog stuff AND have my EGR deleted as well with no custom tune and don't run into any issues.
 
TAB & TAD solenoid valve eliminators – eliminate codes 81 & 82 and 44 & 94

Don’t do this if you have a catalytic converter H pipe. The catalytic converters must have the air from the smog pump or they will clog up and choke.

See www.Newark.com for the resistors to replace the TAB & TAD solenoids

http://www.newark.com/jsp/Passives/Wirewound/OHMITE/43F82RE/displayProduct.jsp?sku=64K8974
If the link fails do a search using the park number
82 ohm, 3 watt wirewound resistor, 94 cents each.
Newark P/N 64K8974
Ohmite part # 43F82RE.

Pay a visit to your local Radio Shack to get some heat shrink and some crimp on tap terminals. They do not stock the resistors. Or you can use the Ford connector pin kit from AutoZone.

pRS1C-2266040w345.jpg

18 gauge crimp on taps Catalog #: 64-3053

Put the resistor inside the heat shrink tubing and crimp the connectors on. I would choose the Ford pin connectors since they should plug in the TAD wiring. That way you haven't modified the wiring so it is easy to re-install the TAD solenoids if emissions testing comes to your area.

52.jpg

Two flat pin connectors.
One 82 ohm, 3 watt resistor.
One piece 3/8" heat sink tubing 2" long.
Two pieces 3/16" heat shrink tubing 1 1/2" long.
Solder the pins onto the resistor leads using electrical solder.
Slide the 3/8" heat shrink tubing over the resistor.
Slide the two pieces of 3/16" heat shrink tubing over the two wires, leaving the flat part of the pins uncovered.
53.jpg


It helps to have the resistor leads straight and not bent as shown in the first picture when you apply heat to the heat shrink tubing. That way, the tubing shrinks more evenly.
Finally, apply heat to shrink all the tubing uniformly.

55.jpg


Bend the leads to fit the spacing on the female TAB & TAD connector sockets.

56.jpg


Push the connector pins of the completed resistor assembly into the empty female TAD or TAD connector sockets on the wiring harness. The resistor assemblies replace the missing solenoids: one resistor assembly per solenoid socket.

Do not crimp on the pins and wrap the mess with electrical tape and say you got the idea from me. If you do, and I hear of it, I will say unkind things about your intelligence and family heritage. Do Quality Work!

This information is for informational purposes only and is intended for use only on off road vehicles. It should not be used on any vehicle operated on public roads.

Operating a vehicle modified in such a manner on public roads is a violation of the EPA codes regarding modification of emission controlled vehicles.