• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Speedo Problems - ive searched forum

  • Thread starter Thread starter fiveohGT
  • Start date Start date Sep 13, 2004
F

fiveohGT

New Member
Jun 22, 2004
353
1
0
Fairfax Virginia
Sep 13, 2004
#1
  • Sep 13, 2004
  • #1
Okay. I have a bouncy speedo, not a speedo off by a couple mph. I replaced the speed sensor, and that made it bounce less. But it still bounces a lot. What should i do now? I want to fix it completely.
-Steve
 

2000xp8

SN Certified Technician
Aug 8, 2003
8,076
1,659
194
NJ
Sep 13, 2004
#2
  • Sep 13, 2004
  • #2
I'd start with a new cable, it may be getting hung up somwhere in the line, i think it's only like 30 bucks or so, if that doesn't fix it goto ebay and get another speedometer.

I'll assume since you changed the speedo sensor that you checked the speedo gear for stripping.
 
F

fiveohGT

New Member
Jun 22, 2004
353
1
0
Fairfax Virginia
Sep 13, 2004
#3
  • Sep 13, 2004
  • #3
Yeah no stripping. The gear was red, and according to how 50resto sells speedo gears, does that mean i have 3.27s? That was the next step I was gunna take...20 bucks actually
 
C

Copperstang87

New Member
Jul 30, 2004
163
0
0
Thunder Bay, Ont
Sep 14, 2004
#4
  • Sep 14, 2004
  • #4
My speedo bounces up and down and then a few secs later it seems to straighten out, I can still usually tell how fast im goin.
 

Papageof

Founding Member
May 6, 2002
322
0
0
Jacksonivlle, FL
Sep 15, 2004
#5
  • Sep 15, 2004
  • #5
Mine used to bounce under 45mph but last night it snapped. 2mo. out of warranty! I have changed it two or three times, it is a piece of cake, just a pita.

Anyway, i think the problem with mine was that imediatly after the sensor the cable hits the exhaust hanger for the h-pipe. That is where it binds cause that is allways were it breaks. I have to shave down the hanger some to get the clearence. Check yours next time you are under there. That could be your problem too.
 
V

v8only

Active Member
Jul 3, 2003
2,378
22
49
Sep 15, 2004
#6
  • Sep 15, 2004
  • #6
the red gear at the trans on foxs are for 3.73 gears, I agree also, change or lube the cable.
 

glowstang93

20+ Year Stangneter
Feb 9, 2003
853
8
39
Illinois
Mar 17, 2006
#7
  • Mar 17, 2006
  • #7
Did changing the cable take care of the problem? My speedo is readable, but it does bounce some 1-2 mph .
 

HardmanGT

Founding Member
Oct 5, 2001
500
0
17
Thomaston, CT
Mar 17, 2006
#8
  • Mar 17, 2006
  • #8
Change the cable. Been there a few times.
 

SPEEDYLIFSAVR

Founding Member
Sep 18, 2000
666
0
16
FL,89 LX 5.0
Mar 17, 2006
#9
  • Mar 17, 2006
  • #9
v8only said:
the red gear at the trans on foxs are for 3.73 gears, I agree also, change or lube the cable.
Click to expand...


I thought white was 3.73?
 

glowstang93

20+ Year Stangneter
Feb 9, 2003
853
8
39
Illinois
Mar 17, 2006
#10
  • Mar 17, 2006
  • #10
To change the cable:I have pulled the cable out before and greased it so I know that part, but to change the cable is there a part that has to be replaced under the car also?
 

glowstang93

20+ Year Stangneter
Feb 9, 2003
853
8
39
Illinois
Mar 20, 2006
#11
  • Mar 20, 2006
  • #11
Will I just be able to open up the dash, disconnect cable from the instrument cluster, pull it up and out. Then slide new cable down into casing? Should this take care of the bouncy speedo? Or do I need to change the speedometer housing too?
 

Papageof

Founding Member
May 6, 2002
322
0
0
Jacksonivlle, FL
Mar 20, 2006
#12
  • Mar 20, 2006
  • #12
I have always changed the sheath too. But if yours is okay... then yes, you could simply shove the new cable down the old sheath. It would be easier. I just prefer to be thorough
 

glowstang93

20+ Year Stangneter
Feb 9, 2003
853
8
39
Illinois
Mar 20, 2006
#13
  • Mar 20, 2006
  • #13
You wouldn't believe how hard it is to find a speedometer cable. Ford, Carquest, and O'Reilly do not have it. I found one at the local Napa and also at Advance Auto Parts. And of course LRS has one.

I have about 75% of the dash apart, just have to take out the pod and then the instrument cluster to get to the speedometer cable. I am going to pull the cable out, clean it and check it out for any burrs, etc. Then if nothing is visible, I am going to relube it and slide it back in. I am going to reassemble enough to go for a drive and see if the needle isn't shaking. If it is, I'll pick up the new cable/housing and do the full install on it.

From Jinchers (sp) , It looks like the end just pulls out of the transmission mount and then reroute the new cable the same way as the old one with the holders. Sounds like fun

While I'm there, I am taking the fuse panel mount out and having the crack in it welded or a new mount cut out at the local welding shop.

I'll let you know what happens on the cable. Thanks again Stangers
 

glowstang93

20+ Year Stangneter
Feb 9, 2003
853
8
39
Illinois
Mar 20, 2006
#14
  • Mar 20, 2006
  • #14
I got the cable out and all wiped down and was getting ready to relube it and then I saw it. The plastic end that goes into the Speedometer has 3 small cracks that start at the base and go toward the point about 1/4". I don't know if this was the cause of the bouncy needle or the fact that there was very little grease on the cable, but I might as well put in a new cable. Off to Napa in the morning. Will decide then if I will change the housing too, but I probably will.

View attachment 483031
 

glowstang93

20+ Year Stangneter
Feb 9, 2003
853
8
39
Illinois
Mar 21, 2006
#15
  • Mar 21, 2006
  • #15
Got it Done

I replaced the casing and the cable and now no more bouncy speedometer. Everyone's instructions were very helpful.

I did have some minor problems. When I pulled the old cable from the VSS it pulled the casing apart from the end. A simple pull on the end with pliers and it came right out. The string I tied to the cable to pull the new through wasn't strong enough so it broke. But with a little fishing I got it thru the grommet and hooked up.

I'm going to split some rubber fuel line and cover the casing where it runs under the floor pan. It crossed under a couple sharper parts of the undercarriage and might as well try to prevent any future rubbing.

While I had the steering column cover apart I also replaced the deteriorating foam circle that goes around the turn signal lever. I just took an air conditioner foam filter, cut out 2 circles and glued them together to give them the correct thickness.

Thanks again
 

squeeeg

Founding Member
Jul 4, 2000
1,905
0
0
Michigan
Mar 22, 2006
#16
  • Mar 22, 2006
  • #16
As for the red gear being 3.27 or 3.73 the answer in in the year of the tranny. 83-89 you have 3.73 gears 90-95 you have 3.27 gears. That is also assuming that your speedo is correct.
 
You must log in or register to reply here.

Similar threads

T
Electrical 93 Foxbody LX 5.0
  • TheJay806
  • Nov 16, 2024
  • Fox 5.0 Mustang Tech
Replies
14
Views
649
Fox 5.0 Mustang Tech Nov 23, 2024
GTOreturns
G
M
Idle control problems
  • miser143
  • Aug 28, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
213
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 29, 2026
DadLife0724
9
New from northern MN
  • 91firecracker
  • Apr 19, 2026
  • The Welcome Wagon
Replies
5
Views
257
The Welcome Wagon Apr 19, 2026
Noobz347
M
1996 GT Speedometer electrical nightmare
  • moon96gt
  • Oct 7, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
195
SN95 4.6L Mustang Tech Oct 17, 2026
CAMTWO1070
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
491
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?