steeda x2 balljoints : leaving spacers out will lower car?

fatts710 · Mar 15, 2008

I just had my front end alinement. I had them use Steeda's agressive set up it lowered my car to two fingers in the front. It handles really well.

2002 Mustang all bolt ons. Stage 2 heads & cams 301 rwh, 315 rwt 4:10 gear, welded torqe boxes & axel, x2 ball joints, UPRbump steer kit, 275/40/17 front & back, 13" rotors front & back, H&R Supersport springs, Summit caster & camber plates

turbogt · Mar 15, 2008

I used x2's to lower mine in conjunction with prokits... Sportlines + x2's =SLAMMED

fiveoho · Mar 15, 2008

turbogt said:
I used x2's to lower mine in conjunction with prokits... Sportlines + x2's =SLAMMED

did the car become darty or wondery after u put in the X2's?

turbogt · Mar 16, 2008

fiveoho said:
did the car become darty or wondery after u put in the X2's?

no, but it did after I put on the azenis...

inphiniti · Mar 16, 2008

turbogt said:
no, but it did after I put on the azenis...

see now its got me wondering. i got the sportlines in. i was just thinkin of gettin the bumpsteer kit, and the 03/04 cobra a arms and run their stock ball joint that it comes with. u think itll lower a little bit more with just that ball joint that comes on the cobras? id like to steer away from getting the x2 at the time since it comes with the a arm

turbogt · Mar 16, 2008

yeah, that is a tough one.. It would be almost impossible to decide without having the cars side by side to see the difference.. I had sportlines on my other mustang and I was going to add x2's because it needed that .5 inch, but I sold it before I got that far.. Otherwise, I could have been able to tell yah.

WhiteCobra95 · Mar 16, 2008

I have the FR D arms to install as well. The stock '03/'04 Terminators already sit pretty low, so I would think that Ford should have setup the ball joints/springs to keet the arms level. Anybody try this? ...with what springs? These A-arms also have a slightly wider track (about .75") This should allow more negative camber on our cars with the stock CC plates.
(I also have the Bullit kit on the shelf but was thinking of replacing the Bullit springs with C-springs from more drop.)

inphiniti · Mar 17, 2008

WhiteCobra95 said:
I have the FR D arms to install as well. The stock '03/'04 Terminators already sit pretty low, so I would think that Ford should have setup the ball joints/springs to keet the arms level. Anybody try this? ...with what springs? These A-arms also have a slightly wider track (about .75") This should allow more negative camber on our cars with the stock CC plates.
(I also have the Bullit kit on the shelf but was thinking of replacing the Bullit springs with C-springs from more drop.)

are u talkin about the kit that has the Tokico shocks/struts(not sure what series, but i know theyre black) the springs and front/rear sway bars? if so i would DEF replace them with the C springs. i had the springs in the front of my car when i first got the kit before i bought the sportlines and it looked like SUCH ass. but i do have those ****ty springs in the rear, it lowered my rear about .5 or so which gives me my raked look iwas lookin for. i guess ill just get the Cobra A arms and so who gives a f when it comes to the ball joint.

i figure, the a arm is an upgrade and technically, has an upgraded, more technologically efficient ball joint than whats on our car for stock.

BaBysARM · Mar 26, 2008

where are you getting your 03-04 cobra a-arms from? and how much?

inphiniti · Mar 27, 2008

BaBysARM said:
where are you getting your 03-04 cobra a-arms from? and how much?

probably buyfordracing.com

hollywoodstang · Mar 27, 2008

I have 03/04 cobra a-arms and ball joint they come with. i used FRPP cobra R springs before they discontinued. i tried both x-2 and regular ball joints a-arms comes with. the steeda x-2 without the spacers will lower you front about .5 or more in my case i liked the regular ball joint cobra a-arms come with. made the car sit even. i did not feel any performance difference between the two. i still my x-2 just in case i change my mind. if you like the front slammed look then install the x-2 without the spacers. you will have to re-align the car afterwards.

fiveoho · Mar 28, 2008

hollywoodstang said:
I have 03/04 cobra a-arms and ball joint they come with. i used FRPP cobra R springs before they discontinued. i tried both x-2 and regular ball joints a-arms comes with. the steeda x-2 without the spacers will lower you front about .5 or more in my case i liked the regular ball joint cobra a-arms come with. made the car sit even. i did not feel any performance difference between the two. i still my x-2 just in case i change my mind. if you like the front slammed look then install the x-2 without the spacers. you will have to re-align the car afterwards.

for the money and what you get, ive thought about going with the 03/04 a arm setup. new arms, all new bushings and new ball joints for like $165.

i still have my X2 ball joints...havent decided what im gonna do yet

hollywoodstang · Mar 29, 2008

if you already have x-2 joints, just use those. cobra arms and your arms do not make much difference. just the turning radius. when you have your control arms out install new arm bushings. poly ones or the ones from steeda works really well.

steeda x2 balljoints : leaving spacers out will lower car?

fatts710

New Member

turbogt

Member

fiveoho

turbogt

Member

inphiniti

Active Member

turbogt

Member

WhiteCobra95

inphiniti

Active Member

BaBysARM

inphiniti

Active Member

hollywoodstang

Active Member

fiveoho

hollywoodstang

Active Member

Similar threads

steeda x2 balljoints : leaving spacers out will lower car?

New Member

Member

Member

Active Member

Member

Active Member

Active Member

Active Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency