• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Steering column swap

  • Thread starter Thread starter pony502
  • Start date Start date Jan 28, 2009

pony502

New Member
Jan 28, 2009
23
0
0
Liverpool N.Y.
Jan 28, 2009
#1
  • Jan 28, 2009
  • #1
Anything I need to know before I put a 88' GT steering column in my 92' GT. Any help would be greatly appreciated.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jan 28, 2009
#2
  • Jan 28, 2009
  • #2
Just take your time....this is all from memory but it will give you an idea....

Disconnect the battery cables

1. Remove the lower dash plastics, trim around the steering wheel
2. Unplug the 4-6 electrical plugs on the column
3. Remove the bolt that attaches the column to the steering shaft, then it will slide out, put a little PB Blaster or WD40 on the joint, they usually stick.
4. Remove the 2 nuts to expose the bolts that hold the column to the dash frame
5. Remove the small support bracket in the front of the dash
6. Pull column out, be careful not to pull on any of the dash harness that is looped around the column.
7. Re-install the oppostite, make sure the intermediate shaft is the same length (this is the part that slides into the steering shaft) If it is shorter or longer pull or puch on the intermediate shaft to make it shorter or longer) It is just pressed into the steering column, it will be tight but it will move. This will allow you to bolt it right back in the same position.


If you want to swap the key switch, put your key in, turn the key to the ON postion and use a small allen wrench or punch to push in the pin to release the key switch. I can't remember off the top of my head if you have to pull the ignition switch out of the way or not... It will require a security torx bit, I think it is a T15. The trim plastic around the wheels were diffferent in the sub 1990 models with out airbags.

Good Luck,

Rick
 

pony502

New Member
Jan 28, 2009
23
0
0
Liverpool N.Y.
Jan 28, 2009
#3
  • Jan 28, 2009
  • #3
Rick, thanks for all the info but all I was really wondering is if all the wiring and harnesses were the same?
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jan 28, 2009
#4
  • Jan 28, 2009
  • #4
I don't remember the wiring being different, but I vaguely remember splicing one plug from a 91 to the 88.....
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jan 28, 2009
#5
  • Jan 28, 2009
  • #5
The wiring is different.The airbag and multifunction (turn signal/high beams/wiper switch) are two items that are different.

AutoZone wiring diagrams

For 79-88 model Mustangs
AutoZone.com | Vehicle Selection - Year

For 89-93 model Mustangs
AutoZone.com | Vehicle Selection - Year

For 94-98 model Mustangs
AutoZone.com | Vehicle Selection - Year
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jan 29, 2009
#6
  • Jan 29, 2009
  • #6
hmmm.. I pulled my tilt from a 88 and it had the same plugs as my 91 except for one small plug and of course the airbags stuff is deleted....

Nice info JR, I always forget about the AZ diagrams
 

pony502

New Member
Jan 28, 2009
23
0
0
Liverpool N.Y.
Jan 30, 2009
#7
  • Jan 30, 2009
  • #7
Thanks for the help guys, I was planning on getting rid of the airbag and cruise anyways. If I run into any problems on the install i'll let you know.
 
You must log in or register to reply here.

Similar threads

4
Drivetrain Wilwood Clutch and Brake Pedal Combo Installation - Help
  • 427stang
  • Jul 8, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
124
Fox 5.0 Mustang Tech Jul 8, 2026
427stang
4
J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
331
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
Swapping clutch pedal hanger-
  • woodsnake
  • Nov 8, 2026
  • Classic Mustang Specific Tech
Replies
0
Views
46
Classic Mustang Specific Tech Nov 8, 2026
woodsnake
L
69 tilt steering column endplay
  • loubischoff
  • Feb 10, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
0
Views
154
1965 - 1973 Classic Mustangs -General/Talk- Feb 10, 2026
loubischoff
L
D
Loud noise(s) from Engine Bay
  • DuluthFoxbody
  • Oct 25, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
14
Views
365
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 5, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?