• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

suspension squeak noise treatment

  • Thread starter Thread starter donnie84
  • Start date Start date Aug 12, 2005
D

donnie84

New Member
Oct 2, 2004
52
0
0
Aug 12, 2005
#1
  • Aug 12, 2005
  • #1
i am replacing the UCA and LCA's, from UPR (HEavy duty GMS ones), mainly cuz the stocks are beat and the bushings are practically gone. it comes with al lthe hardware and such. but i also am doing the bullit suspension kit (shocks/struts, springs and front and rear sway bars). do i need anything else? spring isolators? i am mianly doing this beacuse the stock at 108k makes a decent amount of noise ESPECIALLY from the back (UCA/LCA). the car will also get the ti4res rebalanced and the alignment done. will this pretty much stop the squeaks and noises from the suspension?
 
D

donnie84

New Member
Oct 2, 2004
52
0
0
Aug 12, 2005
#2
  • Aug 12, 2005
  • #2
bump
 
S

spock2001us

Member
Aug 23, 2005
143
0
16
Aug 23, 2005
#3
  • Aug 23, 2005
  • #3
Squeeking

Probably too late for you, but I will post to help others.

My car was squeeking like a old wire bed frame and the front end would groan and whine when I turned the steering wheel. It would also squeal from the front driver side when just wiggleing the steering wheel back and forth. My steering rack had a leak so I put in a new one with new tie rod ends and put it all back together.....the squeeking was gone, but the whine was still there when I wiggled the steering wheel. It was pretty loud and I was so dissapointed that I had spent so much time, put in a new rack and ends, put it all back together and it was still whining.

I then replaced the lower ball joint on the side that was whining (I was too tired to do them both) and that was the problem. My car now stears and turns like it is brand new with no squeeks or other sounds.

If doing the project again, I will plan to replace all ball joints and bushings at the same time, while installing shocks, springs, etc. so that I don't have to go back in and replace one individual part. Ball joints are cheap (like $15 each) and a pain to take in and out, but mine had 125,000 on them.
 

tomustang

Psychotic Member
Founding Member
Jun 8, 2000
3,434
2
78
McLean Hospital
Aug 23, 2005
#4
  • Aug 23, 2005
  • #4
could be the park brake lines, look into that also.
 

slvrbullit302

New Member
Jan 6, 2004
986
1
0
Alabama
Aug 23, 2005
#5
  • Aug 23, 2005
  • #5
Be sure to replace the housing bushings on top of the rearend, I didnot do mine when I installed my UPR's and this past week the ripped out at the track.
 
You must log in or register to reply here.

Similar threads

G
Suspension bottoming out - rear springs bad?
  • gotchopsticks
  • Jul 8, 2021
  • SN95 4.6L Mustang Tech
Replies
9
Views
7K
SN95 4.6L Mustang Tech Aug 1, 2021
1low03gt
Stiffer front springs writeup from the old .net site
  • LILCBRA
  • Oct 24, 2022
  • 1974 - 1978 Mustang II Talk & Tech
Replies
1
Views
1K
1974 - 1978 Mustang II Talk & Tech Oct 29, 2022
Enzio
1
Thinking of selling my 95 GTS
  • #16Stang
  • Jan 20, 2022
  • What is it Worth?!?!?
Replies
5
Views
1K
What is it Worth?!?!? Jan 21, 2022
nickyb
Suspension Brand New Mustang Owner
  • Lee McDonald
  • Feb 26, 2018
  • 2010 - 2014 Specific Tech
Replies
4
Views
1K
2010 - 2014 Specific Tech Apr 3, 2018
SpartaPerformance
Creaking Noise When Braking
  • Nikita2014
  • Nov 14, 2017
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
1
Views
9K
2005 - 2014 S-197 Mustang -General/Talk- Nov 18, 2017
Robert Arco
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?